606845
25
Zoom out
Zoom in
Previous page
1/48
Next page
Page 25
Advanced Operation
PTZ
Pan tilt zoom...PTZ
Pan/Tilt/Zoom (PTZ) Setup:
NOTE: Consult the instruction manual of your PTZ camera for complete
information about your camera, including protocol, baud rate and parity
settings before beginning setup. Enter these settings in the DVR.
Step 1: Connect your PTZ Camera to this DVR
Connect a PTZ camera to the BNC and DC power cables. Also, connect
the communication cable from the PTZ camera to the 485A (TX, +)
and 485B (RX, -) control inputs to the Alarm/PTZ block on the back
of the DVR. Note there is only one set of PTZ control inputs (485A &
485B), however multiple PTZ cameras can be set up by making parallel
connections. See diagram for details and see “PTZ Camera Setup” Info
box for additional information.
Step 2: Configure PTZ Communication Settings:
To access this menu, from the MAIN MENU click ADVANCED then PTZ (see
PTZ Setup image). Use the slider bar on the right of the screen to access all 8
channels available on this DVR. The PTZ setting options for each camera can be
selected independently and are available next to each camera’s channel number.
1. Under PROTOCOL, select PELCO-D or PELCO-P for the selected channel.
2. Under BAUD RATE, select 1200, 2400, 4800, or 9600.
3. Under VERIFY, select ODD, EVEN, MARK, SPACE, or NONE parity bits. Note:
Mark = 1, Space = 0 parity bits.
4. Under ADDRESS, provide an address from 001~255 using the Virtual Key-
board for each PTZ camera.
5. Click APPLY. Click OK in the confirmation window.
6. Click EXIT in all menus until all windows are closed.
Step 3: Configure the Operation & Control of your PTZ
Camera(s):
After your PTZ camera(s) are set up you can control their
operation from your DVR. Note: Individual features must be
available on your camera to operate.
1. In Live View, double click on the Channel with the connected
PTZ Camera to open to full screen view. This selects the
channel to configure and control.
2. From the Quick Access Menu select PTZ. (See image at left)
3. From the PTZ Setup screen you can adjust:
• Pan Speed: Adjusts the speed the camera will move.
• Zoom: “+” Zooms in and “-” zooms out
• Focus: “+” and “-” focuses the picture.
• Iris: “+” lets more light in and “-” removes light from the picture. This is useful to correct
backlight issues.
• Directional keys: Left and Right Arrows control the pan; Up and Down arrows control the tilt. Tip:
Hold the mouse button down while clicking on an Arrow Key and drag the cursor away from the
key to initiate the Auto Movement feature. The camera will pan continuously 360 degrees from
the position it is in or tilt up or down to the limit of the camera until you click OK. This is useful if
you want to manually operate the camera without continuously holding or clicking the arrows.
PTZ Camera Setup
NOTE: It is recommended for best results to use 120Ω
shielded twisted pair cable of a sufficient gauge to meet
your application length. 18 to 22 gauge is usually sufficient.
In addition, be sure to only install the 120Ω terminating
resistor that comes with your PTZ camera in the last parallel connected
camera. Keeping that resistor in all cameras can possibly degrade the
signal and can cause unexpected or loss of operation and control.
Install 120 Ω
terminating
resistor in last
camera only
GND
+ 12V
485B
485A
GND
GND
NO
COM
1
7
6
5
4
3
2
8
ALM IN
PTZ Inputs Conguration
AB AB AB
~
~
PTZ Setup
Select PTZ from the
Quick Access Menu
PTZ Setup - Sub Menu
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BRK PRO-DC8410-520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BRK PRO-DC8410-520 in the language / languages: English as an attachment in your email.

The manual is 5,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info