606724

BRK PRO-D1610 Manual

27
Zoom out
Zoom in
Previous page
1/48
Next page
Page 27
Network Setup for Remote Access
Use the NETWORK SETUP menu to configure your network and DNS settings for remote access. If you are only going to access
the DVR locally from a computer attached to the same router as the DVR, you only
need to configure settings using either the DHCP or STATIC IP. Because you are on
the same network, port forwarding and knowing the public IP address are not
necessary. You will just access the DVR by entering the IP address of the DVR from
the NETWORK setup into the Internet Explorer browser window. If you are going to
take advantage of the Remote Surveillance feature, such as for a smart phone or to
view your system outside of your network over the internet you will need to review
and set up Port Forwarding and the DDNS. After you setup the NETWORK settings
using DHCP , STATIC IP or DDNS, see the REMOTE SURVEILLANCE section for
further instructions.
There are five options for configuring the DVR to be accessed remotely: DHCP,
Static IP, UPnP, PPPOE, and DDNS. To access this menu, from the MAIN MENU
click ADVANCED then NETWORK SETUP. Be sure your router or network is con-
nected to the LAN port on the back of the DVR.
DHCP (Dynamic Host Configuration Protocol)
DHCP is a protocol used by networked devices (clients) to obtain various parameters necessary for the clients to operate in an
Internet Protocol (IP) network. It allows you to quickly connect to your network and obtain an IP address from the router. After
the initial setup, we recommend that you disable DHCP, then select STATIC from the TYPE drop down box and set the IP address
between 1~100. For example, if your IP address is 192.168.0.107, change the last digits to 90 (i.e. 192.163.0.90). This ensures that
port forwarding will not change in the event of power failure or resetting of your network.
To configure DHCP settings:
1. Select DHCP from the TYPE drop down box in the NETWORK SETUP Menu. You should see the message “Getting IP...”
The router will assign an IP address. This is the IP address you will forward port 80 to on the router so you can access the
DVR from remote computers See comment above to configure a static IP.
2. Click APPLY. Click OK in the confirmation window.
3. If necessary, change the Media and Web Port settings
Static IP
You will need to setup the network settings on the DVR to match the settings of the router to which your DVR is connected. This
information can be obtained through your computer. Windows 7, Vista or XP all have similar ways to access this data.
To get the router settings:
1. To access the router’s settings you will need to enter the Command (CMD) panel on your computer. It must be connected
to the same router as your DVR.
• In Windows 7 or Vista, from the “START” menu type “CMD” in the field that says, “Search programs and files” and hit
ENTER or click on the magnifying glass icon.
• In Windows XP select “Run” from the “START” menu. Type “CMD” after the prompt
2. Type “ipconfig” at the prompt and hit enter
3. You will get a screen that contains information similar to what is shown below. Within all of the information shown,
locate the IPv4, Subnet Mask and Gateway addresses. These you will enter into the STATIC IP screen in the NETWORK
SETTINGS menu in your DVR. See next step.
Network Setup
Windows “ipconfig” Info Example
REMOTE Access
Network Setup
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BRK PRO-D1610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BRK PRO-D1610 in the language / languages: English as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info