606732
32
Zoom out
Zoom in
Previous page
1/56
Next page
Page 32
PTZ
VIDEO OPERATION
PTZ
Pan/Tilt/Zoom (PTZ) Setup:
NOTE: Consult the instruction manual of your PTZ
camera for complete information about your camera,
including protocol, baud rate and parity settings before
beginning setup. Enter these settings in the DVR.
STEP 1:
Connect your PTZ Camera to this DVR
Connect a PTZ camera to the BNC and DC power
cables. Also, connect the communication cable from the
PTZ camera to the 485A (TX, +) and 485B (RX, -) control
inputs to the PTZ block on the back of the DVR. Note
there is only one set of PTZ control inputs (485A & 485B),
however multiple PTZ cameras can be set up by making
parallel connections. See diagram for details and see
“PTZ Camera Setup” Info box for additional information.
Step 2: Configure PTZ Communication Settings
To access this menu, from the setup menu click
DEVICE. Then PTZ. This will bring up the PTZ setup
screen. PTZ setting options for each camera can be
selected independently for each camera channel
1. Select the appropriate channel connected to the PTZ
camera using the drop down
2. Under ADDRESS, enter an address from 001–255 using
the virtual keyboard
3. Under protocol, select the appropriate protocol based
on the setting of the camera using the drop down menu
(PELCO-D, PELCO-P, PELCO-D EXT, PELCO-P EXT,
PELCO-D-3)
4. Under BAUD rate, select 1200, 2400, 4800, 9600 as set
in the PTZ camera
5. Click OK to confirm settings. Click EXIT to leave screen
without making changes
LEFT/RIGHT, UP/DOWN, IRIS ZOOM, FOCUS
ZOOM and ZOOM EXCHANGE will reverse the
actions taken when moving or zooming the camera.
For example movement to the left, becomes
movement to the right and movement to zoom
in is reversed to movement to zoom out.
NOTE: Changes to the PTZ setup screen take place
immediately. However, in the event of a power failure,
the settings can revert to the previous settings. It is
recommended to perform a power down and restart
through the drop down menu to save changes in
order for the system to operate with these changed
PTZ setting should a power failure occur.
Configure the operation & control of your
PTZ camera(s):
In live view, double click on the channel with the
connected PTZ camera to open to full screen view. This
selects the channel to configure and control.
1. From the quick access menu select PTZ. this will bring
up the PTZ manual control screen
2. From the PTZ setup screen you can adjust:
Pan speed: Adjusts the speed (1-255) the camera
PTZ Manual Control Screen
PTZ Patrol Screen
PTZ Preset Screen
Install 120 Ω
terminating
resistor in last
camera only
AB AB AB
~
~
PTZ Inputs Configuration
RS485
+ +
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BRK DVRAD1610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BRK DVRAD1610 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info