606729
13
Zoom out
Zoom in
Previous page
1/56
Next page
Page 13
Power On/Off
To power the system On/Off, connect the power cable to the DC 12V port on the rear panel. Press the toggle
switch to the on position in the back of the DVR. At startup, the system performs a basic system check
and runs an initial loading sequence. After a few moments, the system loads a live display view.
User Login
Password
ATTENTION: By default, passwords are disabled on the system. You
do not need to enter a password when accessing any system menus.
However, for security purposes, it is highly recommended to enable
passwords on the system using the Password Menu. See “Password”
section for details on setting up passwords. Right click and
select Login. No password is required when no password is
set up. Right click again to show the quick access menu
Quick Access Menu
When using the mouse, use the Quick Access Menu to
access several system options, including the System
Setup Menu. Select one of the following options:
System Setup: Opens the main system menu
View Layout: Provides a choice of viewing channels on the
monitor
• View 1: Allows viewing of 1 channel
• PIP: Allows viewing of 2 channels,
Picture in Picture
• View 4: Allows viewing of 4 channels
• View 8: Allows viewing of channels 1
through 8, with channel 1 in large view mode
• Split 9: Allows viewing of
channels in a 3 x 3 channel grid
• Split 16: Allows viewing of
channels in a 4 x 4 channel grid
Video Adjust: Adjust video image settings by channel
PTZ: Opens the PTZ control menu
Clients: Network user status
Snapshot: Allows you to take a photo of the
channel that the cursor is on, and save to HDD
Photos: Review save Snapshots, and upload to USB drive
Record Setup: Access to recording settings
for each channel, begin manual recording
Playback: Open the Search Menu
and playback recorded video
Clear Alarm: Cancel alarms
Shutdown: Allows a choice of logging out,
powering down or restarting the DVR system
INITIAL SETUP
SYSTEM OPERATION
Main Viewing Screen
User Login Menu
Power Switch
NOTE: Powering down stops the system. The power LED is still on. The only way to fully power down
the system is by turning the power off & on with the power switch on the back of the DVR.
System Start Up
Powering your DVR and Cameras
The power supply included with the DVR is rated for 5 amps. Normally, this is enough to power both the
DVR and supplied cameras. However, using aftermarket cameras or a larger number of cameras may sur-
pass the capability of the power supply, causing the systerm to shut down. Most devices should be marked
with the Amperage rating, but some may be marked by wattage. In this case, Amp usage can be found by
dividing Watts by Volts, or A=W/V. The power supply should be upgraded if it surpasses 80% of its rating
(i.e., 4 amps for a 5 amp power supply), to compensate for momentary spikes in current draw. Note: One Amp equals 1000 milliamps
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BRK DVRAD0405 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BRK DVRAD0405 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info