767942
13
Zoom out
Zoom in
Previous page
1/151
Next page
Glissez l'élément de liaison 3 entre la
coque 5 et la partie inférieure du siège
6.
Astuce ! L'habillage des sangles 10
(voir image à la page 10) peut être
ouvert pour simplifier l'opération.
Décrochez les bretelles 2 de l'élément
de liaison 3.
Attention ! Une fois décroché,
l'élément de liaison ne doit pas glisser
dans la partie inférieure du siège.
Retirez les bretelles 2 des fentes pour
ceinture 1 de la coque et de la housse.
Glissez la plaque métallique 8 des
épaulières 9 depuis l'arrière à travers
les fentes pour ceinture 1.
Astuce ! Posez la plaque métallique
comme figurant sur la photo sur la
sangle et glissez-la en position
verticale à travers la fente.
Glissez les plaques métalliques 8 dans
le sens inverse à travers les nouvelles
fentes pour ceinture correspondantes
1.
Enfilez les bretelles 2 dans les fentes
pour ceinture 1 dans lesquelles vous
avez également fait passer les
épaulières 9.
Attention ! Veillez à ne pas torsader ni
inverser les bretelles. La bretelle doit
reposer sur la sangle de l'épaulière.
Pull the connecting piece 3 forward
between the seat shell 5 and the seat
base 6 .
Tip! The belt cover 10 can be opened
to do this (see picture on page 10).
Unhook the shoulder straps 2 from the
connecting piece 3.
Caution! After unhooking the
connecting piece, do not allow it to slip
down into the seat base.
Pull the shoulder straps 2 out of the belt
slots 1 from seat shell and cover.
Push the metal plate 8 of the shoulder
pads 9 from behind through the belt
slots 1.
Tip! Position the metal plate on the belt
as shown and push it on its side
upwards through the slot.
Push the metal plates 8 in the reverse
direction through the new relevant belt
slots 1.
Thread the shoulder straps 2 into the
same belt slots 1 through which you
threaded the shoulder pads 9.
Caution! Do not twist or interchange
the straps. The shoulder strap must lie
on the strap of the shoulder pad.
Ziehen Sie das Verbindungsteil 3
zwischen der Sitzschale 5 und dem
Sitzunterteil 6 hervor.
Tipp! Die Gurtabdeckung 10 (siehe
Bild auf Seite 10) kann dazu geöffnet
werden.
Hängen Sie die Schultergurte 2 aus
dem Verbindungsteil 3 .
Vorsicht! Das ausgehängte
Verbindungsteil darf nicht in das
Sitzunterteil rutschen.
Ziehen Sie die Schultergurte 2 aus den
Gurtschlitzen 1 von Sitzschale und
Bezug.
Schieben Sie die Metallplatte 8 der
Schulterpolster 9 von hinten durch die
Gurtschlitze 1.
Tipp! Legen Sie die Metallplatte wie
abgebildet an den Gurt und schieben
Sie sie wie abgebildet durch den
Schlitz.
Schieben Sie die Metallplatten 8 in
umgekehrter Richtung durch die neuen
passenden Gurtschlitze 1.
Fädeln Sie die Schultergurte 2 in die
Gurtschlitze 1 ein, durch die Sie auch
die Schulterpolster 9 gefädelt haben.
Vorsicht! Gurte nicht verdrehen oder
vertauschen. Der Schultergurt muss
auf dem Gurt des Schulterpolsters
liegen.
170316_Main-P4_D-GB-F.fm Seite 12 Donnerstag, 16. März 2017 7:53 07
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Britax-Romer FIRST CLASS PLUS - 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Britax-Romer FIRST CLASS PLUS - 2017 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 17,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info