Manual Britax-Romer BABY-SAFE i-SIZE BASE (page 2 of 2) (English)

767944

Zoom out

Zoom in

1/2

SAFETY NOTES

9. Pull on the base station to check it is engaged on

both sides.

10. Ensure that the support leg 07 is fully rotated; the

red mark at the top of the support leg 07 must

no longer be visible.

11. Press both grey adjustment buttons 06 and pull

the support leg 07 out until it is secured against

the vehicle ﬂoor and the green mark 14 is fully

visible.

DANGER! The green mark 14 must be fully

visible on the support leg 07. The support leg 07

must never be suspended in mid-air or support-

ed by other objects.

Ensure that the support leg 07 does not lift the

base station from the seat.

12. Only BABY-SAFE i-SIZE FLEX BASE: Follow

the steps in chapter “8. Adjusting the inclination”.

13. Take hold of the base station with both hands

and push it with equal pressure on both sides to-

wards the vehicle backrest until the base station

is touching it.

Please take the time to read these instructions carefully and

keep them to hand in the designated storage compartment 13

on the base station at all times! The instructions must be kept

with the base station if the latter is passed on to a third party.

DANGER! For the protection of your child:

• In the event of an accident with a collision speed of more than

10 km/h, the base station may be damaged without the damage

becoming immediately visible. In this case the base station must

be replaced. Please dispose of it properly.

• As a rule, have your base station checked if it was damaged

(e.g if it falls on the ground).

• Regularly check all important parts for damage. Ensure that all me-

chanical parts, in particular, are fully functional.

• Never lubricate or oil parts of the base station.

•

Never leave your child unattended in the

infant carrier and base station

in the vehicle.

• Park in such a way that you can always stand on the pavement when

you place the infant carrier in the vehicle or take it out.

• Protect the infant carrier and the base station from intensive direct

sunlight when they are not in use. The infant carrier can get very hot

in direct sunlight. Children's skin is sensitive and could be harmed.

•

The more snugly the belt ﬁts over your child's body, the better they will

be protected. Therefore, avoid putting thick clothes on your child under

the belt.

• The installation and warning stickers are an important part of the

base station and must not be removed.

• The infant carrier is not intended to hold your baby for prolonged

periods of time. The semi-recumbent position in the infant carrier will

always put a strain on your baby's spine. Take your baby out of the

infant carrier as often as possible – this includes interrupting long car

rides. Do not keep your baby in the infant carrier once it has been

removed from the car.

• Lock the backrests of the vehicle seats (for example, engage the

latch on the foldable rear seat bench).

• Never try to secure a baby on your lap with the vehicle seat belt

or by holding onto them.

• Do not place objects in the footwell in front of the base station sup-

port leg.

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or an accident, unsecured persons

or objects may cause injury to other vehicle occupants. Please always

check that:

• the backrests of the vehicle seats are locked (i.e. that any foldable

rear seat bench latch is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel

shelf) are secured.

• all persons in the vehicle have their seatbelts fastened.

• the child safety seat is always secured when it is in the vehicle, even

if no child is being transported.

WARNING! For your protection when handling the child seat:

•

To avoid damage, ensure that the

base station

is not jammed in be-

tween hard objects (car door, seat rails, etc.).

•

Keep the

base station

in a safe place when it is not in use. Do not

place any heavy objects on the

base station

and do not store it direct-

ly next to sources of heat or in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour,

leather, etc.) may sustain signs of wear and tear when using child safety

seats. For optimum protection of your car seat covers, we recommend

using the BRITAX RÖMER car seat protector from our range of acces-

sories.

PAGE II

2. Rotate the support leg 07 outwards until

it stops.

3. Push the green safety button 05 and the red

release button 04 on both sides of the seat

towards each other. This ensures that both

hooks on the ISOFIX locking arms 03 are open

and ready to use.

4. Pull the grey lever

towards the support leg

until the ISOFIX locking arms 03 are fully

extended.

5. Place the base station against the direction

of travel on a suitable vehicle seat.

TIP: Depending on the design, there could

be a gap between the contact surface of the

base station and the vehicle seat. This does

not present a safety problem when using the

base station.

6. Position the two ISOFIX locking arms 03

directly in front of the two insertion aids 02 .

7. Push both ISOFIX locking arms 03 into the

insertion aids 02 until the ISOFIX locking

arms 03 engage on both sides with a clicking

sound.

DANGER! The green safety button 05 must

be visible on both sides in order for the base sta-

tion to be properly fastened.

8. Take hold of the base station with both hands

and push it with equal pressure on both sides

towards the vehicle backrest until the base

station is touching it.

DANGER! An airbag hitting the infant carrier can cause serious

injuries to your baby, possibly resulting in death.

Do not use the infant carrier and base station in passenger seats with

activated front airbags! For seats with side airbags, please observe the

instructions in your owner's manual.

INSTALLATION IN THE VEHICLE

Preparatory activities:

1. If your vehicle is not ﬁtted with ISOFIX insertion aids as standard,

clamp the two ISOFIX insertion aids 02 , which are included in the

scope of delivery of the seat*, with the cutout pointing upwards

to the two ISOFIX fastening points 01 of your vehicle.

TIP: The ISOFIX fastening points are located between the surface

and the backrest of the vehicle seat.

* The insertion aids facilitate the installation of the child safety seat with the use of the ISOFIX

fastening points and prevent damage to the car seat covers. If the insertion aids are not being used,

remove them and keep them in a safe place. For vehicles with a foldable backrest, the insertion aids

need to be removed before folding the backrest.

Any problems which occur are usually caused by dirt or foreign objects on the insertion aids and

on the hooks. Remove soiling or external objects to rectify such problems.

Removing the infant carrier from the base

station

DANGER! Ensure that the handle 15 is in the

upper position A.

Pull and hold the grey release latch

2. Lift the infant carrier until the ﬁxation prongs 17

release from the ﬁxation slots 08 .

WARNING! Keep a ﬁrm grip on the infant carri-

er while doing this.

3. Remove the infant carrier from the base

station.

To adjust the inclination:

Park your vehicle on as ﬂat a surface as possible.

2. Press and hold the grey inclination adjustment

button 09 and, at the same time, pull the top

part of the base station 12 gradually upwards.

Every time it clicks into the next level, check

if the inclination is sucient.

DANGER! When swivelling the top part

of the base station 12 down, ensure that you

do not trap your ﬁngers.

3. Set the inclination so that the inclination indica-

tor 10 is green.

DANGER! The base station cannot be used

if the inclination indicator 10 is red.

4. Release the grey inclination adjustment button

09 and check that the top part of the base

station is properly engaged.

DANGER! When installing the base station

in another vehicle, the inclination must again

be adjusted from the ﬂattest position.

Fitting the infant carrier to the base station

DANGER! Ensure that the handle 15 is in the

upper position A.

DANGER! Ensure that the top surface of the

base station 12 is free of foreign bodies.

Place the infant carrier against the direction

of travel on the base station (baby is facing

backwards).

2. Snap the infant carrier into place so that

it makes an audible clicking sound.

3. Check if the indicators are green on both

sides.

DANGER! The indicators must be green

on both sides.

4. Pull on the infant carrier handle 15 to check

it is fully engaged.

USING THE INFANT CARRIER

ADJUSTING THE INCLINATION

Depending on the vehicle model, there can be dierences in the vehicle

seat inclination which can have an impact on your child’s seating position.

It is always recommended that the seating position be as upright

as possible. You should therefore set the inclination to be only as ﬂat

as your child’s constitution requires.

Opening the ISOFIX

Pull the grey lever

towards the support leg

2. Push the green safety button 04 and the red

release button 05 on both locking arms 03

towards each other. The locking arms release.

Pull the grey lever

towards the support leg

and press both locking arms 03 at the same

time towards the support leg until they are fully

retracted.

►The base station can now be removed.

DANGER! The child safety seat must always

be secured when it is in the vehicle, even

if no child is being transported.

REMOVAL:

DISASSEMBLY/DISPOSAL

11.

0503

DISPOSAL:

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover

Residual waste, thermal utilisation

Plastic parts According to the labelling in the

corresponding container

Metal parts Container for metals

Belt straps Container for polyester

Buckle and tongue Residual waste

For the safety of your child, before every journey in the car

check that:

►the ISOFIX locking arms 03 are fully engaged on both sides in the

ISOFIX fastening points 01 and that both safety buttons 05 are

fully green,

►the support leg 07 rests ﬁrmly on the vehicle ﬂoor, and the green

mark 14 on the support leg foot is visible,

►the support leg 07 does not lift the base station from the seat,

►the infant carrier is fully engaged in the base station,

►the infant carrier is only installed on the front passenger seat

if no front airbag can strike the infant carrier,

►the infant carrier is fastened against the direction of travel.

For the safety of your child, before every journey in the car

check that:

►the ISOFIX locking arms 03 are fully engaged on both sides in the

ISOFIX fastening points 01 and that both safety buttons 05 are

fully green,

►the support leg 07 rests ﬁrmly on the vehicle ﬂoor, and the green

mark 14 on the support leg foot is visible,

►the support leg 07 does not lift the base station from the seat,

►the infant carrier is fully engaged in the base station,

►the infant carrier is only installed on the front passenger seat

if no front airbag can strike the infant carrier,

►the infant carrier is fastened against the direction of travel.

CLEANING

10.

The plastic parts can be cleaned using soapy water. Do not use

harsh cleaning agents (such as solvents).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Britax-Romer BABY-SAFE i-SIZE BASE in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Britax-Romer BABY-SAFE i-SIZE BASE

Britax-Romer BABY-SAFE i-SIZE BASE User Manual - German - 2 pages

Britax-Romer BABY-SAFE i-SIZE BASE User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Britax-Romer BABY-SAFE i-SIZE BASE Manual

Product: