767908

Britax-Romer ADVANSAFIX i-SIZE Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
click
04
02
05
11
24
23
30
30
08
20
21
20
22
05
17
18
08
19
20
12
14
13
b
c
a
12
13
14
13
12
15
0506
02
01
07
08
08
10
10
click
04
02
05
11
07
click
46
07
14
46
07
46
29
46
1 cm
16
13
05
click
27
25
28
11 26
25
11
29
29
07
11
17
11
46
11
25
27
28
46
1. PREPARATORY STEPS
1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.
1.2 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.
1.3 Follow the steps under “Fastening the XP-PAD” in Section 4.4 “FASTENING /
REMOVING THE XP-PAD”.
2. Place the child seat facing forward on an approved car seat.
Make sure that the backrest 30 is flush with the backrest of
the car seat.
Tip! If the headrest of the car seat prevents the child seat
from being fastened properly, it should be removed (see
vehicle’s instruction manual). Secure the removed headrest
in a suitable place in the vehicle so that it will not be tossed
around.
1. PREPARATORY STEPS
1.1 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.
1.2 Follow the steps under “Fastening the XP-PAD” in Section 4.4 “FASTENING /
REMOVING THE XP-PAD”.
3. FASTENING THE ISOFIX
3.1 Position the two ISOFIX locking arms 04 directly in front of
the two insertion aids 02 .
3.2 Push the two ISOFIX locking arms 04 into the insertion aids
02 until the ISOFIX locking arms 04 engage on both sides
with an audible click.
DANGER! The green locking button 05 must be visible on
both sides indicating that the child seat is correctly fastened.
The
ADVANSAFIX i-SIZE
is not permanently installed in the vehicle. It is simply secured
along with your child by the vehicle’s 3-point seat belt.
To adjust the seat angle:
Pull the adjustment handle 23 forwards and push/slide
the seat pan 24 into the desired position.
DANGER! The seat pan 24 must be rmly engaged, what-
ever the position. Pull on the seat pan 24 to check that it
has engaged.
TIP! You can adjust the tilt angle of the child seat 24 even
while your child is sitting on it. Tighten the vehicle seat belt
after adjusting the seat angle if you use the child seat with
the vehicle seat belt (B1 and B2).
7. SECURING YOUR CHILD
4. PRESSING THE CHILD SEAT BACKWARDS
Push the child seat firmly backwards as far as it will go.
5. CHECKING FOR CORRECT FASTENING
Shake the child seat to check that it is securely fastened
and check the locking buttons 05 to make sure that the two
indicators are fully green.
6. Follow the steps in Section 7 “SECURING YOUR CHILD”.
2. Place the child seat on the car seat. Ensure that the back-
rest 30 is flat against the backrest of the car seat.
Tip! If the headrest of the car seat prevents the child seat
from being fastened properly, it should be removed (see
vehicle’s instruction manual). Secure the removed headrest
in a suitable place in the vehicle so that it will not be tossed
around.
3. Follow the steps in Section 7 “SECURING YOUR CHILD”.
A properly adjusted headrest 07 ensures optimal protection for
your child on the child seat. Regularly check that the height of
the headrest 07 is suitable for the body height of your child:
The headrest 07 must be adjusted so that the shoulder straps
08 are at the same level as your child’s shoulders, or slightly
higher.
A correctly adjusted headrest 07 ensures that the diagonal
belt 11 is optimally positioned and gives your child optimum
protection. Regularly check that the height of the headrest 07 is
suitable for the body height of your child:
The headrest 07 must be positioned so that two fingers can be
inserted between the headrest 07 and your child's shoulders.
To adjust the height of the headrest to fit your child:
1. Press and hold the adjustment handle 10 on the back ofthe
headrest 07 .
2. The headrest 07 is now unlocked and can be moved to the
desired height. When you release the adjustment handle 10 ,
the headrest 07 locks into place.
3. Place the child seat on the car seat.
4. Sit your child on the child seat and check the height.
Repeat this procedure until the headrest 07 is at thecorrect
height.
1. If your vehicle is not fitted with ISOFIX insertion aids
as standard, clamp the two insertion aids 02 (which
are supplied along with the seat*), with recess facing
upwards, into the two ISOFIX fixing points 01 in your
vehicle.
TIP: The ISOFIX fixing points are located between
theseat surface and the backrest of the car seat.
2. Move the headrest of the car seat to its topmost position.
3. Pull the grey handle 03 at the back of the child seat until
the ISOFIX locking arms 04 are fully extended.
4. On both sides of the ISOFIX locking arms, squeeze the
04 green locking button 05 and the red release button
06 together. This ensures that both hooks on the ISOFIX
locking arms 04 are open and ready to use.
* The insertion aids make it easier to install the child seat using the ISOFIX fixing points and they
prevent damage to the car seat covers. If they are not being used, remove them and keep them
in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before
folding the backrest.
Any problems that occur are usually caused by dirt or external objects on the insertion aids and
onthe hook. Remove the dirt or external objects to resolve such problems.
4.1 Preparing ISOFIX
First please read the section describing the desired installation method in Section 5.
►The shoulder straps 08 must be adjusted so that they arehori-
zontal or just above your child’s shoulders.
►The shoulder straps 08 must not be passed behind the child’s
back, or placed level with or above the child’s ears.
The shoulder straps are adjusted as follows:
1. Loosen the 5-point harness 09 on the child seat as far
aspossible.
2. Press and hold the adjustment handle 10 on the back ofthe
headres t07 .
3. The unlocked headrest 07 can now be moved to the desired
height. When you release the adjustment handle 10 , the
headrest 07 locks into place.
4. PREPARATORY STEPS
6. ADJUSTING THE SEAT ANGLE
100 - 150 cm
With car seat belt
B2
100 - 150 cm
With ISOFIX + car seat belt
B1
The seat shell of the
ADVANSAFIX i-SIZE
can be used in three di󰀨erent reclined
positions. The
ADVANSAFIX i-SIZE
is approved for use as follows:
Seat angle Body height
Upright position 76 - 140 cm
Middle position 76 - 150 cm
Lying position 76 - 150 cm
4.3 Adjusting the headrest (100 - 150 cm)
4.2 Adjusting the headrest (76 - 102 cm / ≤ 21 kg)
The XP-PAD must only be used for installation methods B1 and B2.
1. PREPARATORY STEPS
1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.
1.2 Follow the steps in Section 4.2 “ADJUSTING THE HEADREST (76 - 102 cm /
≤ 21kg)”.
1.3 If you reset the child seat from installation method B1 or B2 to A, follow the
steps “Removing the XP-PAD” in Section 4.4 “FASTENING/REMOVING THE
XP-PAD”.
76 - 102 cm / ≤ 21 kg
With ISOFIX + Top Tether
A
2. PREPARING THE TOP TETHER
2.1 Unhook the snap-on hook 12 of the top tether 13 from the
fastening on the back of the child seat.
3. FIXING THE TOP TETHER
Attach the snap-on hook 12 to the anchorage point recom-
mended in your vehicle's instruction manual.
CAUTION! Check that you are not using luggage hooks
instead of the top-tether anchorage points.
Look for the following symbol in your vehicle:
4. FASTENING THE ISOFIX
4.1 Position the two ISOFIX locking arms 04 directly in front of
the two insertion aids 02 .
4.2 Push the two ISOFIX locking arms 04 into the insertion aids
02 until the ISOFIX locking arms 04 engage on both sides
with an audible click.
DANGER! The green locking button 05 must be visible on
both sides indicating that the child seat is correctly fastened.
5. PRESSING THE CHILD SEAT BACKWARDS
Push the child seat firmly backwards as far as it will go.
6. CHECKING FOR CORRECT FASTENING
Shake the child seat to check that it is securely fastened
and check the locking buttons 05 to make sure that the two
indicators are fully green.
7. TIGHTENING THE TOP TETHER
Tighten the top tether 13 , until the belt tension indicator 16
turns green and the top tether 13 is tight.
2.2 Take the top tether 13 out of the pouch 14 and lay it over
the child seat.
2.3 Place the child seat in the direction of travel on an ap-
proved car seat. Adjust the backrest angle of the car seat
so that the gap between the car seat and the child seat is
as small as possible.
2.4 Take the top tether 13 and press the metal tongue 15
away from the belt to extend it, and pull the top tether 13
at the snap-on hook 12 .
2.5 Guide the top tether 13 in the middle between the bars of
the headrest 07 , for integrated headrests on the side closer
to the top tether 13 anchorage point of the vehicle.
9. LOOSEN THE SHOULDER STRAPS
To loosen the shoulder straps, press the adjustment button
18 while at the same time pulling both shoulder straps 08
forward.
CAUTION! Do not pull the shoulder cushions 19 .
10. OPEN THE HARNESS BUCKLE
To open the harness buckle 20 press the red button onthe
buckle.
11. SET THE CHILD IN THE CHILD SEAT
Place your child in the child seat.
Check that the harness buckle 20 is facing forwards.
12. PLACE THE SHOULDER STRAPS
Pass the shoulder straps 08 over your child’s shoulders.
WARNING! Do not twist or swap the shoulder straps, as
this will remove their protective function.
13. FASTENING THE HARNESS BUCKLE
Take the two buckle clips 21 and hold them together before
inserting them in the harness buckle 20 – they must make an
audible click when inserted.
14. TIGHTENING THE ADJUSTMENT STRAP
Pull the adjustment strap 22 until the strap lies flat andsnug
around your child’s body.
WARNING! The hip belts must be positioned aslowas
possible across your child's hips.
Before each journey, in order to ensure your child’s safety, make
sure that ...
►the child seat is engaged on both sides with the ISOFIX locking arms 04
intheISOFIX fixing points 01 and that both locking buttons 05 are fully green;
►the child seat is securely fastened;
►the top tether 13 is tight over the backrest of the car seat and the belt tension
indicator 16 is green;
►the child seat belts fit snugly around the child’s body without causing constriction;
►the shoulder straps 08 are correctly adjusted and are not twisted;
►the shoulder cushions 19 are in the correct position for your child’s body;
►both buckle clips 21 are fully engaged in the harness buckle 20 ;
►the SICT side impact protection 17 is correctly installed and functional.
8. ADJUSTING THE SICT
Turn the SICT 17 anti-clockwise (on the side nearer theve-
hicle door) until there is a gap of 5 mm between itand the
vehicle door, or until it is fully unscrewed.
Fastening the XP-PAD
1. Remove the XP-PAD 46 from the storage pouch14 .
2. Fasten the XP-PAD 46 to the headrest 07 of the child seat.
3. Place the XP-PAD 46 on the side of the child seat closer to
the vehicle door.
4. Pass the elastic XP-PAD retaining strap 46 into the light
green belt holder 29 on the headrest 07 until it is fully in the
belt holder 29 without twisting.
4.4 FASTENING / REMOVING THE XP-PAD
Removing the XP-PAD
1. Pass the elastic XP-PAD retaining strap 46 out of the light
green belt holder 29 .
2. Remove the XP-PAD 46 from the headrest 07 of the child
seat.
3. Store the XP-PAD 46 in the storage pouch 14 .
1. Turn the SICT 17 anti-clockwise (on the side nearer theve-
hicle door) until there is a gap of 5 mm between it and the
vehicle door or until it is fully unscrewed.
13. Tighten the car seat belt by pulling on the diagonal belt 11 .
Before every journey, for your child’s safety, check that ...
►the child seat is engaged on both sides with the ISOFIX locking arms in the ISOFIX
fixing points and both locking buttons are fully green (only applies to B1 | with
ISOFIX and car seat belt);
►the child seat is securely fastened;
►the lap belt is passed through the dark green belt guides on both sides of the seat
cushion,
►the
lap belt is passed through the dark green
SecureGuard.
►the diagonal belt on the car’s seat belt buckle side is also passed through the dark
green belt guide on the seat cushion,
►the diagonal belt is passed through the light green belt holder at the headrest,
►the XP-PAD and SICT side impact protection are correctly installed and used,
►the diagonal belt runs diagonally backward,
►the straps are tight and not twisted,
►the car’s seat belt buckle is not placed in the dark green belt guide on the seat
cushion.
DANGER!
If your child tries to open the car’s seat belt buckle 27 or insert the
diagonal belt 11 in the dark green SecureGuard 26 , stop your vehicle immedi-
ately, or as soon as possible. Check that the child seat is correctly fastened and
that your child is correctly secured. Explain to your child the dangers caused by
such actions.
2. Let your child sit in the child seat and place the XP-PAD 46
over the chest area of your child. If you find that the retraction
force of the 3-point seat belt is not enough to ensure that the
seat belt is tight (against the child), the child seat can be used
without the XP-PAD 46 .
3. Pullout the car seat belt, pass it in front of your child and
into the car seat belt buckle 27 .
DANGER! Check that the car seat belt is not twisted,
otherwise the full protective action of the restraint system
will be impaired.
4. Insert the buckle clip in the car seat belt buckle 27 until
there is an audible click.
5. Pass the diagonal belt 11 and lap belt 25 on the car’s
seatbelt buckle side 27 into the dark green belt guide 28 on
the seat cushion.
DANGER! The car’s seatbelt buckle 27 must not be near
the dark green belt guide 28 .
6. Also pass the lap belt 25 on the other side of the seat cush-
ion into the dark green belt guide 28 .
DANGER! The lap belt 25 must be placed as low as possi-
ble over your child’s hips on both sides.
7. Pass the lap belt 25 into the dark green SecureGuard 26 .
DANGER! Do not pass the diagonal belt 11 into the dark
green SecureGuard 26 .
8. Pass the diagonal belt 11 into the light green belt holder
29 at the headrest 07 so that it is fully in the belt holder 29
without twisting.
Tip! If the backrest 30 is covering the light green belt holder
29 , you can adjust the headrest 07 upwards. The diagonal
belt 11 can then be easily inserted. You can then adjust the
headrest 07 back to the correct height.
9. Make sure that the diagonal belt 11 passes over the collar-
bone, not the neck, of your child and that the button on the
dark green belt holder is 29 fully closed.
Tip: You can adjust the height of the headrest 07 again in
the vehicle.
10. Open the Velcro fastener on the XP-PAD 46 and fold the top
part of the XP-PAD 46 to the side.
11. Insert the diagonal belt 11 in the die nubby surface of the XP-
PAD 46 .
12. Close the XP-PAD 46 again by folding the folded part back and
closing the Velcro fastener.
DANGER! The diagonal belt 11 must run diagonally back-
wards. You can adjust the belt routing with the adjustable belt
deflector in the vehicle.
DANGER! The diagonal belt 11 must never run forwards
towards the belt deflector on the vehicle. In this case, use the
child seat on the back seat only.
5. INSTALLATION & USE
DANGER! Remove the child seat from the vehicle. Never carry the child seat in
the car if it is not fastened properly.
A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)
1. Loosen the top tether 13 by pushing the metal tongue 15
away from the belt.
2. Release the snap-on hook 12 from the anchorage point in the vehicle and lay the
top tether 13 to the front over the child seat.
3. Loosen the ISOFIX fastening on both sides by squeezing the green locking button
05 and red release button 06 together.
4. Pull the seat forward and store the top tether 13 in the storage pouch 14 and
attach the snap-on hook of the top tether 13 to the fastening on the back of the
child seat.
5. Move the ISOFIX locking arms 04 back into the seat pan 24 .
B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)
1. Press the release button on your car seat buckle
2. Open the XP-PAD 46 on the Velcro fastener and remove the diagonal belt 11 .
3. Open the light green belt holder 29 by pressing the button on the belt holder 29
backwards, then pull out the diagonal belt 11 .
Only for installation method with ISOFIX:
4. To release the ISOFIX fitting, squeeze the green locking button 05 and red release
button 06 together, first on one side then on the other.
5. Move the ISOFIX locking arms 04 back into the seat pan 24 .
8. REMOVING THE CHILD SEAT
8.1 UNFASTENING YOUR CHILD:
8.2 REMOVAL:
A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)
To unfasten your child, press the red button on the buckle.
B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)
To unfasten your child, use the release button of your car seat buckle.
TIP! The XP-PAD can remained applied for easier use on the diagonal belt of your
vehicle, the diagonal belt must be retensioned before every journey; see: Section 7
step 11 [page II].
03
04
46
14. Make sure that the XP-PAD 46 is centred on the chest.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Britax-Romer ADVANSAFIX i-SIZE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Britax-Romer ADVANSAFIX i-SIZE in the language / languages: English as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Britax-Romer ADVANSAFIX i-SIZE

Britax-Romer ADVANSAFIX i-SIZE User Manual - German - 2 pages

Britax-Romer ADVANSAFIX i-SIZE User Manual - Dutch - 2 pages

Britax-Romer ADVANSAFIX i-SIZE User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info