497163
12
Zoom out
Zoom in
Previous page
1/142
Next page
10
Die eingestellten Parameter können nun übernommen werden.
Bei gewünschter Parameterübernahme gehen Sie wie folgt vor:
Taster 1 x betätigen (< 1 Sekunde), bis die Meldung
„Reset“ erscheint und blinkt.
< 1 sec
Taster 1 x betätigen (> 2 Sekunden), bis die Gesamt-
kapazität (bei 0% Verschnitt) und das aktuelle Datum
erscheinen.
> 2 sec
Die eingestellten Parameter wurden übernommen.
Hinweis: Erfolgt länger als 30 Sekunden keine Eingabe, kehrt die Anzeige in den Standby- bzw.
Betriebsmodus zurück, ohne geänderte Parameter zu übernehmen.
Anzeigeeinheit von vorn in ca. 10 mm Höhe einsetzen und nach unten schieben. Die Nasen am
Anzeigeteil müssen in die Nuten am Messkopf eingeführt werden. Weiter mit Kapitel 5.4 Ein-
spülen/Entlüften für Filtersysteme mit und ohne Mess- und Anzeigeeinheit.
5.3 Verschnitteinstellung
Bestimmung der Verschnitteinstellung
Entsprechend der Anwendung und der ermittelten Karbonathärte wird anhand der Verschnitt- und
Kapazitätstabelle (Kapitel 7) die Verschnitteinstellung bestimmt. Anschließend wird der Verschnitt
wie folgt an der Verschnitteinstellschraube
19
eingestellt:
Verschnitteinstellschraube
19
drehen, bis der gewünschte Verschnitt (03) mit der Markierung
übereinstimmt.
!
Achtung: Inbusschlüssel 6 mm oder 7/32" verwenden.
!
Achtung: Die Verschnitteinstellschraube darf nicht über den Anschlag hinaus gedreht werden,
um Beschädigungen zu vermeiden.
5.4 Einspülen/Entften von Filtersystemen mit und ohne Mess- und Anzeigeeinheit
Hinweis: Zum Einspülen/Entlüften wird ein 10-Liter-Eimer benötigt.
Filtersystem horizontal hinlegen.
Spülventil
9
vollständig öffnen.
Eingangsventil
7
am Eingangsschlauch
6
komplett öffnen, dabei Spül-
schlauch im Eimer festhalten. Spülmenge mindestens 10 Liter bei einem
Mindestvolumenstrom von 3 l/min (180 l/h).
Spülventil
9
schließen, Filter hinstellen und Eimer entleeren.
Spülventil
9
vorsichtig öffnen, dabei Spülschlauch im Eimer festhalten.
Spülmenge erneut mindestens 10 Liter.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brita PURITY 1200 Steam at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brita PURITY 1200 Steam in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info