753042
6
Zoom out
Zoom in
Previous page
1/16
Next page
6 Art.-nr.: 611885-G
Modbus Interface
Wire colour
C1 brown
C2 yellow
C3 green
C4 white
Connecting %rinN Connect to 5enovent ([cellent 6N\
3rocedure connecting +59 appliance to building automation s\stem
z Connect the HRV appliance to the Brink Connect module and the building automation system as shown in the above diagram.
z
Remove the Modbus RS485 termination resistor if not necessary! If several Brink Connects are used in one line, no more
than 2 resistors (RS485) may be installed in the line.
z
Connect the HRV appliance/building automation system to the mains.
z
If required, set values at the HRV appliance through the display or a - for a Sky appliance temporary connected - control unit
or Brink service tool
z
Observe the following steps when connecting several Brink Connect modules:
-
&RQQHFWWKH¿UVW%ULQN&RQQHFWPRGXOHWRWKHEXLOGLQJDXWRPDWLRQV\VWHP
-
Change the Modbus slave address via Modbus address 1000 into a unique address.
-
Repeat the above steps for each Brink Connect module to be connected.
Modbus Interface
5eading values
Functie
code
0x03
Modbus
address Description correction
factor
sig-
ned 9alues remarNs
4002 Appliance type 1 no
4004 Applianc version (basic/ Plus) 1 no
4009 Current Temperature from outdoors sensor [°C] 0.1 no
4010 Current Temperature from dwelling [°C] 0.1 yes
4011 Current Pressure supply duct [Pa] 1 no Note: Only at constant volume fan4012 Current Pressure exhaust duct [Pa] 1 no
4013 3UHVHWDLUÀRZUDWH>P
3
/h] 1 no
4016 Imbalance permissible 1 no 0 = Flow rate supply equals extract /
1 = Imbalance permissible
4022 Preset imbalance [m
3
/h] 1 yes
4028 &XUUHQWVXSSO\ÀRZUDWH>P
3
/h] 1 no Note: Only at constant volume fan
4029 &XUUHQWH[KDXVWÀRZUDWH>P
3
/h] 1 no
4030 Bypass valve position 1 no 0 = Initialising / 1 = Opening / 2 = Closing
3 = Open / 4 = Closed / 255 = Status un-
known
4031 Operation bypass valve 1 no 0 = Automatic /1 = Bypass valve closed/
2 = Bypass valve open
4037 Preheater status 1 no 0= initialising/ 1= not active/ 2= active/
3= test mode/ 255= status unknown
4038 Preheater power [%] 1 no
4039 Current fault code 1 no HRV appliance error code (0 = no error)
4040 Error message 1 no 0 = Filter clean / 1 = Filter fouled
4041 Geo heat exchanger mode 1 no 0= Off, 1 = On
4047 Geo heat exchanger min. temp. [°C] 0.1 yes
4053 Geo heat exchanger max. temp. [°C] 0.1 yes
4059 Nr. selected CO
2
sensor (max. 4 pieces) 1 no Note: Only a mounted eBUS CO
2
sensor
will be supported.
4060 Value selected CO
2
sensor [PPM] 1 no
Connectors Brink
Connect screwable
up to 1.5 mm²
1
2
3
4
C1
C2
C3
C4
C1
C2
C3
C4
Modbus-
System
pwr
1
+5V
2
GND
3
SDA
4
SCL
5 A
485
6 B
485
I2C <> Modbus
cdefgh
%rinN
Connect
Fabrieks-
instelling
jumpers
Control pcb in
5enovent ([cellent
of 5enovent 6N\
6upplied
connecting cable
Cable-mounted
edge connector
pw
Green LED
power supply
RS485 termination resistor
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brink Connect at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brink Connect in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info