474043
2
Zoom out
Zoom in
Previous page
1/34
Next page
Teile
-
Aufbau
l
Parts
-
Construction
Mle:
Aufbau
/
Parts: Construction:
0
Schrauben (Tubus)
/
Screws (tube)
0
Teleskop-Tubus
Telescope
tube
0
Sucherfernrohr
View-finder
scope
0
Justierschrauben (Sucher)
Adjusting-screws (view-finder)
0
Befestigungsschrauben (Sucher)
Fastening screws (view-finder)
0
Objektiv
Objective
0
Okular-Stutzen
Eyepiece connection
0
Scharfeinstellungsrad
Focus
wheel
0
Tubus-Anschluß
Tube connection
0
Montierung
Mount
@
Stativ-Kopf
Tripod
head
@
Zubehör-Ablage
Accessory tray
@
Befestigungsschrauben (Ablage)
Fastening screws
(tray)
(D
Stativbeine
Tripod legs
0
Vertikal-Feineinstellung
/
Vertical
fine-adjustment
Teile: Optik
/
Parts:
OPtics:
0
Azimutale
Montierung
/
Azimutaf mount
0
Sucherfernrohr
/
View-finder
scope
0
Schrauben (Stativkopf)
/
Screws (tripod
head)
0
Okulare
/
Eyepieces: 20 +
12,5
+ 6mm
0
Schrauben (Stativbeine)
/
Screws (tripod
legs)
0
Umkehr-Linse
1,5x
/
Erecting lens
1,5x
0
Zubehör-Ablage + Schrauben
/
Tray + Screws
0
Mondfilter
/
Moon
filter
0
D
1.
Allgemeineshandort:
Bevor Sie mit dem Aufbau beginnen, wählen Sie
einen
eeigneten Standort
fur
Ihr Teleskop.
Es wir
3
Ihnen helfen, wenn Sie dieses Gerät an
einem Ort aufbauen, an dem Sie freie Sicht auf
den Himmel haben, einen stabilen Untergrund
und genügend Platz um sich herum.
Nehmen Sie zuerst alle Teile aus der
Verpackung. Überprüfen Sie anhand des
Schaubildes, ob alle Teile vorhanden sind.
Wichtig: Ziehen Sie alle Schrauben nur
“handfest” an und vermeiden Sie so ein
“Überdrehen” der Schrauben.
2. Aufbau
-
Stativbeine:
Zuerst ziehen Sie das
jeweils mittlere Stück der
drei Stativbeine (13) auf
die gewünschte Länge
heraus.
Danach werden die
Feststellschrauben (5)
in die Stativbeine einge-
schraubt und fest ange-
dreht.
GD
: 1.
GeneraVLocation:
Before you begin construction, you must
choose
a suitable location for your
telescope.
lt will help you, if
ou build this appliance in a
place,
where you
rl
ave a
clear
view on the
skies,
a stable footing and
sufficient
space
around you.
Remove all the
Parts
from the
packaging
first.
Check, using the diagram, whether
all the
Parts
are there.
Impottant: Only do the screws up
finger
tight
and avoid over tightening them.
2.
Construction
-
Tripod-legs:
First, pull out the middle
piece
of
each
of the
three tripod legs (13)
to the desired wished
length.
The
locking
screws (5)
are then inserted into
the tripod legs and
screwed in securely.
3. Aufbau
-
Montierung + Stativ:
Damit die Montierung (9)
und das Stativ fest verbun-
den sind, muß die
Montierung in den
Stativkopf (10) eingesetzt
werden.
Hierzu werden die
Schrauben (4) mit einer
Unterlegscheibe
durch das
Bohrloch im Stativkopf
und der Halterung an der
Montierung gesteckt.
Danach wird die zweite
Unterlegscheibe
und die
Flügelmutter auf die
Schraube aufgesetzt und
angedreht. Verfahren Sie
auf die gleiche Weise bei
3. Construction
-
Mount + tripod:
So that the mount (9) and
the tripod are
securely connected, the
mount must be attached
to the tripod
head
(10).
The screws (4) are
inserted with a
washer
through the boring in
the
tripod-head
and the
mounting on the mount.
The
second
washer
and
the wing nut are screwed
on and tightened.
Proceed in the same
man-
ner with the two
remai-
ning mountings, until the
mount and
den zwei übrigen Halterungen, bis die
tripod are solidly connected as one.
Montierung fest mit dem Stativ verbunden ist.
Achten Sie darauf, daß die Halterungen
(XI
für
Make sure that the mountings (X) for the
die Zubehör-Ablage an den Stativbeinen nach
accessory
storage tray are on the inside of the
innen gerichtet sind.
tripod
legs.
-2-
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser VENUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser VENUS in the language / languages: English, German as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info