784594

Bresser Messier Exos 1 Manual

31
Zoom out
Zoom in
Previous page
1/44
Next page
appendIx c: polar alIGnment
Looking at or near the Sun will cause instant and irreversible damage to your eye! 31
* Optional accessory for EXOS-2
Appendix C: Polar Alignment
The Polar Alignment Viewfinder
Normally, a rough alignment with the celestial pole is sufficient for visual
purposes. However, for those observers who need to meet the more
demanding requirements of astrophotography, the polar alignment
viewfinder allows the telescope mount to be more precisely aligned with
true North. The EXOS-2 Mount can be equipped with a red LED illumina-
tion for the finder scope (available separately).
Adjusting the polar viewfinder (EXOS-2 only)
A: Calibrating the month circle at the polar viewfinder scope
(best done while daytime)
1. Point the viewfinder against a bright surface (not in any case at the
sun!) and see the scaled line with the center cross (Fig. 36). Turn the
viewfinder’s eyepiece until the scales are focussed.
2. Now turn the month circle against the viewfinder until the 1st of May hits
the vertical line. The month circle is secured by a counterring; it should
be able to be turned but it should not come loose. Now you can put the
viewfinder back into the RA axis
3. On the month circle, there’s a second scale, marked “E 20 10 0 10 20
W”. Take a white pencil and mark the point on the viewfinder that is right
above the “0”. This can be also done by using a small piece of colored
tape.
B: Aligning the viewfinder’s optical axis to the RA axis
1. Starting at the polar home position (see p. 18), loosen the Dec lock, turn
the Dec axis by 90° and re-engage the Dec lock again. In this position,
the optical axis of the viewfinder is free.
2. Point the viewfinder at a terrestrial objekt like a phone pole, the tip of
a church tower or equiv. so that it lines up with the center cross of the
reticle.
3. Ascertain whether the object moves out of the center cross when the
mount is rotated around its Dec axis.
4. If this is the case, correct 50% of the error by adjusting the hex screw of
the viewfinder holder. Now correct the remaining error by repositioning
the mount. Turn the RA axis by 90 / 180° and repeat this process until
the center cross stays on the desired object.
Polar alignment by using the polar viewfinder
(EXOS-2 only)
1. Set the polar home position (p. 18). Loosen the Dec lock, turn the Dec
axis by 90° and re-engage the lock.
2. Loosen the RA lock (33, Fig 1 d)
3. Remove the dust caps
4. If not done yet, remove the isolaton pad from the viewfinder’s
illumination (see p. 10, step 13).
5. Turn the illuminator switch clockwise to a comfortable brightness and
look throug the viewfinder. If necessary, focus the viewfinder until reticle
and stars appear sharp.
6. In the following step 7, use the latitude adjustment screws (Fig 1 d, 26)
and the azimuth adjustment screws (Fig 1 d, 27) to do the necessary
fine adjustments
Fig. 36: The view inside the polar
alignment viewfinder reticle (the
four stars show an association
near the southern celestial pole)
Fig. 35: The polar alignment
viewfinder*
Rotary knob for
illumination
Polar finder
eyepiece
3)
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser Messier Exos 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser Messier Exos 1 in the language / languages: English as an attachment in your email.

The manual is 2.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser Messier Exos 1

Bresser Messier Exos 1 User Manual - German - 48 pages

Bresser Messier Exos 1 Quick start guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info