784594

Bresser Messier Exos 1 Manual

10
Zoom out
Zoom in
Previous page
1/44
Next page
Looking at or near the Sun will cause instant and irreversible damage to your eye!
10
9.
Attach viewfinder bracket
(Abb. 9b). Locate the viewfinder bracket
screws (15, Fig. 1b and Fig. 9a) and remove the nuts from the screws.
Slide the holes in the viewfinder bracket over the viewfinder bracket
screws. Replace the nuts and tighten to a firm feel only.
9a. Attach viewfinder tube:. Back off the viewfinder collimation screws (5,
Fig. 1b) and slide the viewfinder tube into the bracket. Orient the view-
finder eyepiece as depicted in Fig. 1b. Tighten the collimation screws
to a firm feel. See Aligning the viewfinder, page 14.
10. Insert the eyepiece: NT models (Fig. 10a): Lift to remove the dust cap
from the eyepiece holder on the focuser assembly. Set the dust cap
aside in a safe place and replace it when you have finished observing
to protect the eyepiece assembly. Back off the eyepiece thumbscrews
(1, Fig. 1a) and insert the supplied 25mm eyepiece (3, Fig. 1a) into the
the eyepiece holder. Tighten the holder thumbscrews to a firm feel to
secure the eyepiece. AR models (Abb. 10b): Lift to remove the dust
cap from the eyepiece holder on the focuser assembly. Set the dust
cap aside in a safe place and replace it when you have finished obser-
ving to protect the eyepiece assembly. Back off the eyepiece thumb-
screws (1, Fig. 1b) and slide the diagonal prism into the holder and
tighten the thumbscrews to a firm feel only. Insert the supplied 25mm
eyepiece (3, Fig. 1b) into the the diagonal prism. Tighten the prism‘s
thumbscrews to a firm feel to secure the eyepiece.
11. Adjust the height of the tripod: Adjust the height of the tripod by
loosening the tripod lock knobs (Fig. 11). Extend the sliding inner
section of each tripod leg to the desired length; then tighten each knob.
Adjust the tripod to a height that is comfortable for viewing.
13. Remove Plastic from Reticle LED*: The polar alignment reticle LED
(30, Fig. 1d) contains two watch batteries. The reticle‘s LED is shipped
with a plastic strip between the two batteries to protect battery life.
Unthread both the thumbscrew (F) and the threaded lid (E). Remove
the plastic strip before using. Refer to the reticle assembly in Fig. 13b
and note the orientation of the batteries. Place the batteries (C) into
the battery holder (D) before inserting into the reticle container (A).
NOTE:
The 2” focusers of the Messier Series from AR-102 or NT-130 on have a
built in extension tube. Depending on the accessories used, or when using
a camera, it might not be possible to reach the focus. Focus travel to the
inside might not be sufficient in the standard configuration. To reach focus,
unscrew the eyepiece holder, then the following 25mm extension tube.
Screw the eyepiece holder back in place.
Fig. 11: Adjust the tripod height
using the leg lock knobs.
Leg lock knob
Fig. 9b: The finder scope assem-
bly has a dovetail bracket, that
fits the holder that is mounted on
the optical tube.
assemblInG exos-1
* Optional accessory for EXOS-2
Fig. 10b: Insert eyepiece into
diagonal prism and tighten
thumbscrews.
Eyepiece
Holder
Thumbscrews
Diagonal
prism
Viewfinder
AR
Fig. 10a: Insert eyepiece intor hol-
der and tighten thumbscrews.
Eyepiece
Holder
Thumbscrew NT
Viewfinder
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser Messier Exos 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser Messier Exos 1 in the language / languages: English as an attachment in your email.

The manual is 2.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser Messier Exos 1

Bresser Messier Exos 1 User Manual - German - 48 pages

Bresser Messier Exos 1 Quick start guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info