611622

Bresser AR-90 Manual

20
Zoom out
Zoom in
Previous page
1/44
Next page
Looking at or near the Sun will cause instant and irreversible damage to your eye!
20
ma I n t e n a n c e a n d se r v I c e
Alignment (Collimation) of the
Newtonian Optical System
All Bresser Newtonian telescopes are precisely collimated at the factory 
before packing and shipment, and it is probable that you will not need to
make any optical adjustments before making observations. However, if
the telescope sustained rough handling in shipment, you may need to re-
collimate the optical system. Such re-collimation is not a difficult procedure
in any case.
The collimation procedure for the short focal length-Newtonians is slightly
different from that of other Newtonian reflecting telescopes, because of the
„fast“ f/5 focal ratio of the primary mirror. In typical Newtonian reflectors with 
more conventional focal ratios (i.e. longer focal ratios), when the observer
looks down the focuser tube (without an eyepiece in the focuser), the images
of the diagonal mirror, primary mirror, focuser tube, and the observer‘s eye
appear centered relative to each other. However, with the short focal ratio
primary mirror of the Newtonian, correct collimation requires that the diagonal
mirror be offset in 2 directions: (1) away from the focuser and (2) towards the
primary mirror, in equal amounts. This offset is  approximately 1/8“ in each 
direction. Note that these offsets have been performed at the factory prior to
shipment of your telescope. It is only necessary for you to confirm that the
telescope has not been badly jarred out of collimation, and to perform the
final fine-tuning of Step 4, below.
Fig. 31a shows a correctly collimated Newtonian telescope, as it appears
when viewed through the focuser with the eyepiece removed.
To check and, if necessary, set the optical collimation, follow these steps:
1. Observe through the focuser and orient your body so that the telescope‘s
primary mirror is to your right. The diagonal mirror will appear centered
as shown (2, Fig. 31a). If the diagonal appears off center, then adjust the
4 collimation screws on the plastic diagonal mirror housing.
2. If the reflection of the primary mirror (3, Fig. 31a) is not centered on the
surface of the diagonal mirror, adjust the 4 collimation screws on the
plastic diagonal mirror housing to center the reflection. As described
above, the 4 collimation screws (Fig. 31b) on the plastic diagonal mir-
ror housing are used for two different adjustments during the collimation
procedure.
b c d e f g
Fig.31a
Note:
The AR-(refractor) models do not
need any collimation
b
Focuser drawtube
c
Secondary mirror
d
Reflection of primary mirror
e
Reflection of secondary mirror
f
Reflection of observer’s eye
g
Primary mirror clips
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser AR-90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser AR-90 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info