Manual Bresser 9070710 VA colour LCD - National Geographic (page 20 of 52) (English, German, French, Spanish)

785323

Zoom out

Zoom in

1/52

20 / 52

7 Before commissioning

NOTICE

Avoid connection faults!

In order to avoid connection problems between the devices, the following points must be observed

during commissioning.

1. Place the base unit (receiver) and sensor (transmitter) as close together as possible.

2. Connect the power supply to the base unit and wait until the indoor temperature is displayed.

3. Establish power supply for the sensor.

4. Set up/operate the base unit and sensor within the effective transmission range.

5. Make sure that the base unit and the radio sensor are set to the same channel.

When changing the batteries, always remove the batteries in both the base unit and the sensor and

reinsert them in the correct order so that the radio connection can be re-established. If one of the two

devices is operated via a mains power connection, the power connection for this device must also be

disconnected briefly when changing the battery. If, for example, only the batteries in the sensor are re-

placed, the signal cannot be received or can no longer be received correctly.

Note that the actual range depends on the building materials used in the building and the position of

the base unit and outdoor sensor. External influences (various radio transmitters and other sources of

interference) can greatly reduce the possible range. In such cases, we recommend finding other loca-

tions for both the base unit and the outdoor sensor. Sometimes a shift of just a few centimetres is

enough!

8 The first steps

Follow the bullet points in order, to ensure a successful setup.

1. Setting up power supply (base station)

2. As soon as the radio signal icons for the outdoor sensors start flashing, insert the batteries into the

sensors immediately, otherwise the station will eventually switch to DCF radio signal search. No

outdoor sensors can be connected during the DCF radio signal search. If new outdoor sensors are

to be connected, please start from point 1 again.

3. When the radio signal next to the time flashes, the DCF radio signal is being searched for. During

this search, the outdoor sensors cannot be connected. The DCF search process may take up to

15 minutes and then restarts every hour if the DCF connection is not successful until the connec-

tion is successful.

9 Setting up power supply

Base device

1. Insert the DC connector into the connection socket of the base station.

2. Insert the mains plug into the power outlet.

3. The device is energized directly.

4. Wait until the indoor temperature is displayed on the base station.

NOTICE!For permanent operation, mains power supply is recommended. Alternatively a

power supply with batteries is also possible, to keep the time setting in case of power fail-

ure. Proceed as follows:

5. Remove the battery compartment cover.

6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

7. Replace the battery compartment cover.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 9070710 VA colour LCD - National Geographic in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0.65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 9070710 VA colour LCD - National Geographic

Bresser 9070710 VA colour LCD - National Geographic User Manual - Dutch - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bresser 9070710 VA colour LCD - National Geographic Manual

Product: