632930

Bresser 88-45001 Manual

18
Zoom out
Zoom in
Previous page
1/172
Next page
18
GB
tripod rests on one leg. Finally, set the tripod
down on all legs, so that it stands straight.
Loosen the three locking clips (11) (Figure 1
+ 4) on the tripod legs, pull each individual
tripod leg out until it has reached the desired
length (see gure 4), close up the locking
clips and set the tripod down on a sturdy, even
surface.
TIP:
A small water level on the accessory tray can
help you position your tripod horizontally.
4. Mounting the tray:
The accessory tray (10) (Figure 1 + 3) must be
positioned with its at side down in the midd-
le of the tripod leg brace (16) (Figure 1), and
then must be mounted by turning it 60° in a
clockwise direction (Figure 5).
The three projections on the tray plate must
match up to the mounting brackets on the di-
vision bars (12) (Figures 1 + 3) and must snap
into place. If necessary, you may push the tri-
pod leg brace downwards a little.
5. Tube
In order to mount the telescope tube (1) (Fig.
1), loosen the locking screw on the tube
clamp (8) (Fig. 6) and open up the clamp.
Set the tube in the middle of the holder and
snap the clamp shut again. Please screw the
locking screw on the holder tightly, using your
hand only.
Now set the tube (and holder) onto the mount
with the objective opening in the direction
marked (N-marking on the tripod head, nor-
th point and telescope gure on the mount).
Then fasten the tube holder with the clamping
screw of the dovetail adapter on the mount
head (Figure 7).
6. Inserting the Eyepiece
Three eyepieces (18) (Figure 2) and one ze-
nith mirror (19) (Figure 2) come with your te-
lescope. With the eyepieces, you can control
the magnication of your telescope.
Before installing the eyepieces and the zenith
mirror, take the lens cap (21a) out of the eye-
piece holder (6) (Figure 1). Loosen the clam-
ping screws (21) on the eyepiece holder and
insert the zenith mirror. Then screw the clamp
screws (21) back on.
F
1)
1@
1^
G
I
i
2!
h
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 88-45001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 88-45001 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info