729874

Bresser 7002560 W-LAN-Weather-Center-6-in-1 Manual

27
Zoom out
Zoom in
Previous page
1/36
Next page
27 / 36
NOTICE!During the assembly make sure that the upper part of the wind vane is minimum 1.5
metres off the ground. Use the circular level in the sensor head to ensure a level installation. The
windmill must point to the North.
Assembly on a vertical or horizontal tube
1. Insert the stainless steel mounting pole into the mounting hole of the sensor and tighten the
screws firmly.
2. Attach the stainless steel pole to a post or pipe using the 2 U-bolts, mounting clamps and nuts.
10 First Steps
Follow the bullet points in order, to ensure a successful setup.
• Setting up power supply (base station and wireless sensor)
• Mount the remote sensor
• The base station is now in AP mode (LED flashes green) and ready for initial setup.
• Create a Weather Underground account and add the station to your account ("My Profile" / "Add
Weather station"). Here you will receive a station ID and a password, which will be needed in the next
step.
• Setting up the base station (Estabish Wi-Fi / Router connection)
• Viewing weather data via web, mobile or tablet
11 Base station
Once the power is connected, the console status LED will light up red, and after a few seconds, the
base station will show the Wi-Fi connection status:
1. If the base station has not yet been connected to a router, it first switches to AP (Access Point
mode) mode. The status LED flashes green. The station is now ready for setup. Follow the instruc-
tions in Section 13.
2. If the base station was already connected to a router, it will try to re-establish the connection. The
status LED flashes blue.
3. After successfully connecting to the router, the status LED lights up blue. Die Station is now ready
for use.
Status LED Base station:
Status LED Status
Startup LED flashes red for approx. 7 seconds
AP mode (Access Point Mode) to set up the
router connection
LED flashes green
Connection establishment or connection failed LED flashes blue
Connected to Wi-Fi router LED lights up blue
Firmware update LED flashes red
Refresh the upload data by pressing the RE-
FRESH button
LED flashes purple
12 Signal transmission
The base station will automatically connect to your multi outdoor sensor and (if available) to your in-
door sensor. You can also press the Wi-Fi / SENSOR button to start a manual search for the remote
sensors. When the connection is successful, the status LED will turn blue.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 7002560 W-LAN-Weather-Center-6-in-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 7002560 W-LAN-Weather-Center-6-in-1 in the language / languages: English, German as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 7002560 W-LAN-Weather-Center-6-in-1

Bresser 7002560 W-LAN-Weather-Center-6-in-1 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info