Manual Bresser 7002550 Comfort Weather Center 5in1 (page 8 of 24) (English)

729973

Zoom out

Zoom in

1/24

8 / 24

7 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting

operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re-

place them in the correct order, so the remote connection can be re-established. If either of the

devices is mains-powered, the power supply must be disconnected for a short moment also for this

device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the

remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-

mote units. Due to external influences (various RC devices and other sources of interference), the

maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the

remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a

few inches!

8 Setting up power supply

Base unit

1. Insert the DC connector into the connection socket of the base station.

2. Insert the mains plug into the power outlet.

3. The device is energized directly.

4. Wait until the indoor temperature is displayed on the base station.

NOTICE!For permanent operation, mains power supply is recommended. Alternatively a

power supply with batteries is also possible. Proceed as follows:

5. Remove the battery compartment cover.

6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

7. Replace the battery compartment cover.

8. Wait until the indoor temperature is displayed on the base station.

NOTICE!When switching from mains power supply to battery power supply or vice versa,

the power supply is being disabled for a short moment for technical reasons. In this process

all settings made previously, will be deleted.

Remote sensor

9. Loosen the screw at the battery compartment cover with a small Philips screwdriver and remove

the cover.

NOTICE!Make sure not to lose the thin sealing ring when removing the battery compart-

ment cover. It is an important protection against water infiltration and often adheres at the

battery compartment cover.

10. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

11. Press RESET button. The function indicator lights up for a short moment.

12. Put the sealing ring back onto the edge of the battery compartment.

Je viens d'acheter une station Météo BRESSER 5 en 1 impossible d'avoir l'affichage de la température intérieure malgré une attente assez longue pour mise en service après branchement sur secteur et piles
mise en place des piles dans capteur extérieur tout s'affiche normalement sauf température indoor
Que faire
Submitted on 6-10-2022 at 11:08
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 7002550 Comfort Weather Center 5in1 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 7002550 Comfort Weather Center 5in1

Bresser 7002550 Comfort Weather Center 5in1 User Manual - German - 24 pages

Bresser 7002550 Comfort Weather Center 5in1 User Manual - Dutch - 24 pages

Bresser 7002550 Comfort Weather Center 5in1 User Manual - French - 68 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bresser 7002550 Comfort Weather Center 5in1 Manual

Product: