Manual Bresser 7002540 PROFI W-LAN WETTER CENTER (page 13 of 20) (English, German)

729972

Zoom out

Zoom in

1/20

41. Barometer reading

42. Barometer measurement unit (hPa / inHg / mmHg)

43. Alarm on

Rainfall (Fig. 15)

44. Time range record indicator

45. HI Alert and alarm on

46. Current rainfall rate

47. Rainfall unit (in / mm)

Multifunctional histogram (Fig. 16)

48. Histogram variable

49. Histogram

50. Hourly records indicator

BEFORE YOU START

IMPORTANT!

1. Insert batteries for the main unit before doing so for the 6 in 1 outdoor

sensor.

2. Place the main unit as close as possible to the remote unit.

3. Position the remote unit and main unit within the effective transmis-

sion range.

When changing batteries always change batteries in the main unit as well

as all remote units and replace them in the correct order, so the remote

connection can be re-established. If batteries are exchanged in only one

of the devices (i.e. the remote sensor) the signal can’t be received or

can’t be received correctly.

Note, that the effective range is vastly affected by building materials and

position of the main and remote units. Due to external inuences (var-

ious RC devices and other sources of interference), the maximum dis-

tance can be greatly reduced. In such cases we suggest to position the

main unit and the remote sensor at other places. Sometimes all it takes

is a relocation of one of these components of a few inches!

POWER SUPPLY

Main unit (Fig. 19)

1. Plug the DC power adaptor (D) into the DC jack (25)

2. Press RESET key to re-start the main unit

3. After reset, all LCD segments will show on the display for a short mo-

ment before the unit enters the AP (access point) setup mode and the

LED lights green.

Insert backup batteries (optional)

1. Open the battery compartment door.

2. Install 3 batteries (AAA size 1.5V) strictly according to the polarities

shown.

3. Reinsert the battery compartment door.

The Main unit LED indicator can show the following status:

Status LED status

AP (access point) mode for setup ash green

light

Connected to Wi-Fi router blue light

Search the Wi-Fi router / Connection failed ash blue

light

Firmware update ash red light

Manual sensor pairing mode by pressing the [Wi-Fi /

Sensor] key

ash cyan

light

Refresh the upload data and sync internet time by

pressing the [Refresh] key

ash purple

Indoor sensor (Fig. 3)

1. Open the battery compartment door.

2. Install 2 batteries (AA size 1.5V) strictly according to the polarities

shown.

3. Reinsert the battery compartment door.

NOTE!

1. If you need to re-assign the sensor channel, rstly slide the channel

slide switch to the new channel that you want, then press the [SEN-

SOR] button on the main unit and then press the [RESET] button on the

sensor to pair the sensor with the main unit again.

2. Avoid placing the sensors in direct sunlight, rain or snow.

3. To avoid the sensor's and main unit pairing failure during new setup,

please power up the sensor's rst, and then press the [RESET] button

on the main unit (not on the sensor's).

6-in-1 Multi Outdoor sensor (Fig. 20)

1. Open the battery compartment door.

2. Install 3 batteries (AA size 1.5V) strictly according to the polarities

shown.

3. Reinsert the battery compartment door.

NOTE!

The LED will begin ashing every 12 seconds.

Low battery warning

When it is time to replace the batteries, the respective low battery indi-

cator

will be shown near to the Indoor temperature and humidity

display (batteries for main unit) or near to the Outdoor temperature and

humidity (batteries for remote sensor).

INSTALLATION

Indoor sensor

Use the mounting hole on the back of the sensor to install it on the wall

using a screw. You can also place the sensor directly to e.g. a table.

6-in-1 Multi Outdoor sensor (Fig. 17-18)

Install the wireless 6-in-1 Multi Outdoor sensor in an open location with

no obstructions above and around the sensor for accurate rain and wind

measurement. Install the sensor with the smaller end facing the North to

properly orient the wind direction vane.

Secure the mounting stand and bracket (included) to a post or pole, and

allow minimum 1.5m off the ground.

Fig. 17: Mounting on pole (Pole Diameter 50.8 mm (approx. 2“)).

Fig. 20: Circular level.

Mounting guidelines:

1. Install the wireless 6-in-1 sensor at least 1.5m off the ground for better

and more accurate wind measurements.

2. Choose an open area within 150 meters from the LCD display main

Unit.

3. Install the wireless 6-in-1 sensor as level as possible to achieve accu-

rate rain and wind measurements. A circular level device is provided to

ensure a level installation.

4. Mount the wireless 6-in-1 sensor with the wind meter end pointing to

the North to correctly orient direction of the wind vane.

Step 1:

Plug the stainless steel moun-

ting pole into the sensor's

mounting hole and tighten the

screws.

Screws

Step 2:

Fasten the stainless steel

tube on your x pole with 2

U-bolt, pole mounting clamps

and nuts.

U-bolt

Mounting

clamp

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 7002540 PROFI W-LAN WETTER CENTER in the language / languages: English, German as an attachment in your email.

The manual is 5,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 7002540 PROFI W-LAN WETTER CENTER

Bresser 7002540 PROFI W-LAN WETTER CENTER User Manual - French - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bresser 7002540 PROFI W-LAN WETTER CENTER Manual

Product: