729974

Bresser 7002520 Weather Center 5-in-1 Colour Manual

12
Zoom out
Zoom in
Previous page
1/20
Next page
12
BEFORE YOU START
IMPORTANT!
1. Insert batteries for the main unit before doing so for the remote
sensor.
2. Place the main unit as close as possible to the remote unit.
3. Position the remote unit and main unit within the effective
transmission range.
When changing batteries always change batteries in the main unit as
well as all remote units and replace them in the correct order, so the
remote connection can be re-established. If batteries are exchanged
in only one of the devices (i.e. the remote sensor) the signal can’t be
received or can’t be received correctly.
Note, that the effective range is vastly affected by building materials
and position of the main and remote units. Due to external influences
(various RC devices and other sources of interference), the maximum
distance can be greatly reduced. In such cases we suggest to position
the main unit and the remote sensor at other places. Sometimes all it
takes is a relocation of one of these components of a few inches!
POWER SUPPLY
Main unit (Fig. 15)
1. Plug the power supply adaptor into the DC jack
2. Once the batteries are inserted, all the segments of the LCD will be
shown briefly before entering the radio-controlled time reception
mode.
3. The RC clock will automatically start scanning for the radio-
controlled time signal in 8 seconds.
Insert backup batteries (optional)
1. Open the battery compartment door.
2. Install Button cell CR2032 strictly according to the polarities shown.
3. Reinsert the battery compartment door.
NOTE!
1. If no display appears on the LCD after inserting the batteries, press
the RESET knob by using a pointed object.
2. In some cases, you may not receive the signal immediately due to
the atmospheric disturbance.
Remote sensor (Fig. 16)
1. Open the battery compartment door.
2. Install 3 batteries (AA size 1.5V) strictly according to the polarities
shown.
3. Reinsert the battery compartment door.
NOTE!
1. Ensure the water tight O-ring is properly aligned in place to ensure
water resistant.
2. The red LED will begin flashing every 12 seconds.
Low battery warning
When it is time to replace the batteries, the respective low battery
indicator
will be shown near to the time display (batteries for main
unit) or near to the outdoor temperature (batteries for remote sensor).
INSTALLATION
Remote sensor (Fig. 17-20)
Install the wireless 5-in-1 sensor in an open location with no
obstructions above and around the sensor for accurate rain and wind
measurement. Install the sensor with the smaller end facing the North
to properly orient the wind direction vane.
Secure the mounting stand and bracket (included) to a post or pole,
and allow minimum 1.5m off the ground.
Fig. 17/18: Mounting on pole (Pole Diameter 1" - 1.3" (25 - 33mm)).
Fig. 19: Mounting on the railing.
Fig. 20: Circular level.
Mounting guidelines:
1. Install the wireless 5-in-1 sensor at least 1.5m off the ground for
better and more accurate wind measurements.
2. Choose an open area within 150 meters from the LCD display Main
Unit.
3. Install the wireless 5-in-1 sensor as level as possible to achieve
accurate rain and wind measurements. A circular level device is
provided to ensure a level installation.
4. Mount the wireless 5-in-1 sensor with the wind meter end pointing
to the North to correctly orient direction of the wind vane.
Main station (Fig. 21)
Fig. 21
The unit is designed for desktop or wall mount for easy viewing.
Insert the stand so that the pins on the bottom side reach into the
indentions of the station.
The triangular notch on the backside of the main station can be used
to mount the device on walls with a wall screw (not included).
RECEIVING MEASUREMENTS AND TIME SIGNAL
Once batteries are placed in the remote unit, it will start transmitting
temperature readings at roughly 45 second intervals. As soon as
batteries are installed in the main unit it will start searching for a signal
from the remote sensor for about 3 minutes. Upon successful reception
of the signal, the outdoor temperature will be displayed on the main unit.
The main unit will automatically update its readings at about 45 second
intervals.
Subsequently, the main unit will attempt to receive the DCF radio signal.
The reception symbol
flashes. When the time signal is received
after 3-5 minutes, the current time and date appear in the display. The
reception symbol will now be shown permanently in the display. Date
and time are automatically updated daily at 2:05 o’clock (CET) by the
main unit.
Symbol
Signal
strength
no
signal
weak
signal
acceptable
signal
excellent
signal
Manual pairing after battery change
Whenever you changed the batteries of the wireless 5-in-1 sensor,
pairing must be done manually.
1. Change the batteries to new ones.
2. Press and hold the SCAN button for 2 seconds.
3. Press the RESET button on the sensor.
NOTE!
1. Pressing RESET button at bottom of wireless 5-in-1 sensor will
generate a new code for pairing purpose.
2. Always dispose old batteries in an environmental safe manner.
DATA CLEARING
During installation of the wireless 5-in-1 sensor, the sensors were likely
to be triggered, resulting in erroneous rainfall and wind measurements.
After the installation user may clear all the erroneous data from the
main unit without a need to reset the clock and re-establish pairing.
Simply press and hold the HISTORY button for 10 seconds. This will
clear out any data recorded before.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 7002520 Weather Center 5-in-1 Colour at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 7002520 Weather Center 5-in-1 Colour in the language / languages: English, German as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 7002520 Weather Center 5-in-1 Colour

Bresser 7002520 Weather Center 5-in-1 Colour User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info