Manual Bresser 70-20000 Connect Set (page 22 of 72) (English, German, Dutch, French, Italian, Spanish)

632904

Zoom out

Zoom in

1/72

Creating groups of devices (Group lists)

Speciﬁc groups of devices can be created with enery meters.

1) In “Energy meter” main display, tap the “ i ” on the upper right corner to enter the setting display.

2) Tap “Group List”.

3) Tap ”+” on the upper right to add a group.

4) Select one or more energy meters for the new group.

5) Tap “+” to form a new group.

6) You may change the name and photo of the group. Tap the “Save” button on the upper right corner anytime to save

and exit.

Notes

1) Please ensure the sensors are switched on and registered one by one.

2) When opening the “BresserConnect” App, it will directly go to the last sensor page displayed before exititing the

last time. It may need some time to refresh the sensor data. So please wait for several seconds for updated

measurements to be displayed.

Trouble shooting

General

If you have run the Connect system for a long period of time and one day one of your weather or soil sensor fails to connect

with the system while the rest of the sensors work ﬁne, it’s likely that the battery level in this sensor is low. Please reinstall new

batteries and follow the instruction in the manual to reconnect the sensor to your Connect system again.

Gateway

• 1. New Sensors cannot be successfully registered on the App.

a) Please check whether the App can effectively communicate with the gateway. After pressing the “Connect” button

on the App to register a new sensor, the green LED will start ﬂashing for around 30 seconds. If not, power off the

router and the gateway and then power them on again and retry.

b) The sensor may be too far away from the gateway or there is radio frequency interference nearby. Please put the

sensor closer to the gateway, preferably within direct line-of-sight. Shut off all electrical appliances nearby and retry.

• 2. Sensor data are not updated or no sensor data is displayed or the remote sockets cannot be controlled.

a) Please power off the gateway and power on again and observe the LEDs on the gateway as listed in paragraph 4

below. If no abnormal status is found, please turn off the WiFi feature of your iOS or Android device and then turn it

on again to reconnect to the router. Run the app again.

b) Otherwise, please check on the App whether the sensor status is ‘disconnected’. If yes, please follow the

recommendations in point 3 below.

c) If the problem persists please switch router and Gateway off and on again and try again.

e) If there are many sensors of the same type installed, the memory (RAM) size of your iOS or Android device may

not support the display of all the sensor images on one page. Please delete some of the sensors to see if the

situation can be improved. If this is the cause, you may need a more sophisticated iOS or Android device model

with a larger memory.

• Sensor status has become ‘disconnected’ (an exclamation mark next to the sensor list).

Please try the 3 steps below:

a) Power off the gateway. After a while, power it on again and wait for around 30 seconds until the green LED on the

gateway stops ﬂashing. After powering up, the gateway will scan the presence of the installed sensors within the

ﬂashing period and reconnect them, if the sensors are found.

b) Wait until the next day. At midnight each day, the gateway automatically performs scanning of and reconnection

with installed sensors.

c) If the sensor disconnection is due to a short period radio frequency inteference, it will be automatically reconnected

after the interference has gone. However, if the interference period is long (i.e. more than one hour), then the sensor

can only be reconnected by means of method 1) or 2) above.

• 3.If the reconnection still fails, then it may be caused by one or more of the following reasons:

• The sensor location is marginal or out of reach of the radio frequency reception range. Please move the sensor to a closer

or less blocked location and retry.

• The battery level may be relatively low. Please retry with new batteries.

• The sensor operation software is hung up. Please remove and re-insert the batteries into the sensor and go to the sensor

management page on the BRESSER Connect App and press the RECONNECT button within 30 seconds.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 70-20000 Connect Set in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bresser 70-20000 Connect Set Manual

Product: