729969
39
Zoom out
Zoom in
Previous page
1/44
Next page
Kapitel 3: Häufig gestellte Fragen
1 Was muss ich tun, wenn die Düse verstopft ist?
2 Wie tausche ich die Düse aus?
Schalten Sie den Drucker vor dem Austausch der Düse aus! Trennen Sie den Netzstrom!
Die Spitze des abgeschnittenen Fillaments muss glatt und flach sein.
Überprüfung der Sprinklerbaugruppe:
1. Beim Einsetzen wird der Sprinkler am Ende eingedrückt.
2. So prüfen Sie, ob der Sprinkler eingesetzt ist:
(1) Berühren Sie die schwarze Spange und das Unterteil des Sprinklers;
beides muss fest sitzen und darf sich nicht nach unten bewegen.
(2) Schauen sie auf den schwarzen Spalt und das Unterteil des Sprinklers,
und achten sie darauf, dass nur ein kleiner Spalt vorhanden ist.
Hinweis
Clips
Methode 1: Berühren Sie [Vorwärmen], um den Extruder auf 240°C zu erwärmen.
Nach dem Aufwärmen drücken Sie die Luftrohrverbindung und ziehen das
Fillamentführungsrohr heraus. Prüfen Sie, ob das Fillament gebogen oder die Fillamentspitze
rau ist. Schneiden Sie die Fillamentspitze dann glatt und flach zu und setzen Sie das
Führungsrohr und das Fillament wieder ein. Berühren Sie [Laden].
Methode 2: Falls sich das Ergebnis mithilfe von Methode 1 nicht verbessern lässt, entfernen Sie das
Fillament und drücken sie das Reinigungswerzeug oben in den Extruder um Fillamentreste
aus der Düse zu drücken.
Methode3: Falls sich das Ergebnis mithilfe von Methode 1 und 2 nicht verbessern lässt,
tauschen Sie die Düse aus.
1. Drücken Sie die Klammern rechts und links nach unten und ziehen Sie die Düse ab.
2. Führen Sie einen Fillament von Hand zur die Fillamentaufnahme. Der Fillament muss ausreichend lang
sein, um abgeschnitten werden zu können.
3. Drehen Sie die Fillamentspule manuell gegen den Uhrzeigersinn,
wobei Sie das Fillament etwas zurückschieben.
4. Drücken Sie die Clips rechts und links ein, setzen Sie die neue Düse wieder in den Extruder,
wobei der Düsenschlitz und die Unterseite des Extruders auf identischer Höhe sein müssen.
5. Berühren Sie: [Fillament] - [Laden], Wenn das Fillament aus der neuen Düse austritt,
ist der Wechsel abgeschlossen.
37
Die Spange ist nicht eingesetzt. Die Spange ist eingesetzt.
1� How to solve if the nozzle is clogged?
2� How to replace the nozzle ?
Method 1: Tap [Preheat], heat up the extruder to 240°C, after heating completed, press the
air tube joint and pull out the lament guide tube. Check to see whether the
lament is bended or lament tip is not smooth, cut lament tip smooth and at,
install the guide tube and lament back, Tap [Load] .
Method 2: If method 1 not improving, use an unclogging pin tool to unclog lament.
Method 3: If method 1 and method 2 not improving, please replace the nozzle.
Power off before replacing nozzle! Make sure power off operation!
Please make lament tip smooth and at when cutting off the lament.
1. Press the left and right clips and pull out the nozzle.
2. Push in a length of lament through the lament intake manually, making it long enough
to be cut off.
3. Rotate the lament spool anti-clockwise manually, making lament retreat back a little.
4. Press the left and right clips, install the new nozzle back into the extruder, making the
nozzle slot and bottom of extruder are on the same level.
5. Tap[Filament] -- Tap[Load], nozzle replace completed when you see lament come out of
Whether the assembly of the sprinkler is in place is judged as follows:
1. When installing, must press the sprinkler hard to the end.
2. Check whether the installation is in place:
(1) Touch the black buckle and white sprinkler‘s lower shell, make
sure no sunken.
(2) Look at the black buckle and white sprinkler‘s lower shell,
make sure there is not a large gap in the contact.
Chapter 2: Q&A
new Nozzle.
The buckle is not installed in place. The buckle is installed in place
Notices
Clips
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 2010100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 2010100 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 2010100

Bresser 2010100 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info