729969
33
Zoom out
Zoom in
Previous page
1/44
Next page
31
2.5 Kamera-Bedienungsanleitung
Auto Mode
Idling Printing
Manual Mode
Auto Mode
Manual Mode
Drucken
Werkzeuge
Fillament
Drucken
Werkzeuge
Fillament
Kamera-Bedienungsanleitung
2.5.1. Sie kann über den angeschlossenen Computer geschaltet werden.
Die Kamera und der USB-Wechseldatenträger nutzen dieselbe Schnittstelle.
Die Kamera des W-LAN 3D-Drucker und der USB-Stick des W-LAN 3D-Drucker sind nicht
miteinander kompatibel (das heißt, dass immer nur eines dieser beiden Geräte verwendet
werden kann: entweder die Kamera oder die USB-Wechselfestplatte).
Sie können in der Cloud oder am lokalen Computer zwischen der Kamera und der
USB-Wechselfestplatte umschalten.
Die Verwendung der W-LAN 3D-Drucker-Kamera wird nachstehend erläutert.
Die W-LAN 3D-Drucker-Kamera hat zwei Betriebsmodi: Automatikmodus (Standardmodus) oder
manueller Modus. Der Zugriff auf die Kamera erfolgt über „Werkzeuge -> Einstellungen -> Kamera)
(Werkzeuge-Einstellungen-Kamera) (auf der zweiten Seite). Für den Zugriff auf die relevante Seite,
berühren Sie die Schaltfläche „Kamera“.
Sobald die Kamera erfolgreich eingeschaltet wurde, wird das Kamerasymbol in der
Statusleiste angezeigt. Sobald die Kamera ausgeschaltet wird, wird anstelle des
Kamerasymbols das USB-Wechselfestplattensymbol in der Statusleiste angezeigt.
Automatischer Modus: Während des Druckerbetriebs wird die
Kamera eingeschaltet und die USB-Wechselfestplatte deaktiviert.
Während der Drucker inaktiv ist, wird die Kamera ausgeschaltet
und die USB-Wechselfestplatte ist aktiviert.
Manueller Modus: Der Benutzer kann
nach Belieben zwischen der Kamera
und der USB-Wechselfestplatte
umschalten.
Wenn die Bilder im Browser
angezeigt werden sollen,
müssen Drucker und PC in
demselben Intranet aktiv sein
(das heißt, Drucker und PC sind mit
demselben Router verbunden).
Hinweis
Print
Tools
Filament
Print
Tools
Filament
2�5 The Guide of Using Camera
Camera User Manual
Camera and USB Disk use the same interface, so the use of WIFI 3D Printer‘s camera is
different from that of other models. The use of WIFI 3D Printers camera and the use of
WIFI 3D Printer‘s USB Disk are incompatible (that is, only one (camera or USB Disk) can
be used in the same time). The switching between camera and USB Disk can be realized
through the Cloud or the lower computer. The use of WIFI 3D Printer‘s camera is introdu-
ced as follows.
In respect of the use of WIFI 3D Printer‘s camera, there are two modes, that is automatic mode
(default mode) and manual mode. The route is (Tools->Settings (on the second page) ->
Camera), the user can click the “Camera” button to enter the relevant page.
2�5�1� The switching can be controlled by the lower computer
Automatic Mode: When the printer is working (such as
the printer is printing the les), the camera is turned on
and USB Disk is turned off� When the printer is not wor-
king, the camera is turned off and USB Disk is turned on�
Manual Mode: The switching
between camera and USB Disk
can be controlled by the user
at will�
Notices
When the user wants to use the
browser to view the images,
the printer and PC must be in
an intranet (that is, the printer
and PC connect to the same
router).
After the camera is turned on successfully, the icon of camera will appear in
Status Bar. After the camera is turned off, the icon of USB Disk will appear in
Status Bar in case of successful insertion of USB Disk.
Auto Mode
Idling
Printing
Manual Mode
Manual Mode
Auto Mode
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 2010100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 2010100 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 2010100

Bresser 2010100 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info