729969
25
Zoom out
Zoom in
Previous page
1/44
Next page
23
Einzug
Auswurf
200
/220
Extruder Heizung ein...
Cancel
2.3.3 Fillament
Der Extruder wird auf 220°C erwärmt.
Sobald die Temperatur erreicht ist, führen Sie das Fillament in einem rechten Winkel in den
Extruder ein, bis Widerstand zu spüren ist (das Fillament wird durch das Zuführrad gedrückt).
Das Laden ist abgeschlossen, sobald das Fillament aus dem Extruder austritt
Laden
Der Extruder wird auf 220°C erwärmt. Sobald die Temperatur erreicht ist, wird das Fillament
aus dem Extruder ausgegeben.
Ziehen Sie das Fillament gemäß den Anleitungen heraus.
Führen Sie das neue Fillament in die Fillamentaufnahme ein und berühren Sie [OK].
Das neue Fillament wird aus dem Extruder gedrückt. Der Austauschvorgang ist abgeschlossen,
sobald das neue Fillament aus dem Extruder austritt.
Wechseln
220
/220
ok
Drücke ok wenn das neue
Fillament austritt.
220
/220
Vorheizen abgeschlossen.
laden beginnt...
ok
Einzug
Auswurf
220
/220
Fillament entladen,
bitte warten...
Altes Fillament entfernen
neues einfügen , drücke [ok].
220
/220
ok
Drücke ok wenn das neue
Fillament austritt.
220
/220
ok
2�3�3 Tools
Input
Output
Input
Output
Extruder heating on..
Preheating complete.
charging commencing...
Press ok when the new
lament comes out.
Load
Switch
•The extruder is heated up to 220°C.
•After heat completed, insert the lament into the extruder at an upright angle until some
resistance is sensed (as the lament is pushed through the feeding wheel).
•Load will complete when you see lament come out of extruder.
Filament unloading,
please wait...
Remove Old Filament
insert new, press [ok]
Press ok when the new
Filament comes out.
• The extruder is heated up to 220°C, after heat completed, lament will be unloaded from the
extruder.
• Pull out the lament according to the instruction.
• Insert new lament into the lament intake, tap [OK] ;
• New lament will be pushed into the extruder, replace will complete when you see new lament
come out of extruder.
Cancel
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 2010100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 2010100 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 2010100

Bresser 2010100 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info