655618
7
Zoom out
Zoom in
Previous page
1/68
Next page
GB
7
OWNER'S MANUAL • PATH
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill). If the belt slips, turn another
1/4 turn and repeat the test. When braking heavily
the belt may slip. If the belt keeps slipping despite
repeated adjustments, please contact your local
Bremshey dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects
and malfunctions caused by individual components
may occur in the equipment. In most cases it’s
unnecessary to take the whole device in for repair,
as it’s usually sufficient to replace the defective
part. Always give the model, serial number of
your equipment and in case of malfunctions also
conditions of use, nature of malfunction and any
error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If
after you have reset the treadmill by turning the
power switch off and on again, and the treadmill is
still not operational, contact your local Bremshey
dealer for service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
E1: Speed sensor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
E6, E7: Lift motor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
PROTECTIVE CIRCUIT
The machine will shut off when the electricity
load is above the machines capacity. To restart the
machine, please follow the procedure below:
A. Unplug the power cord from the machines
socket.
B. Push in the safety switch.
C. Replug the power cord into the machines socket.
NOTE! DON’T PUSH IN THE SAFETY SWITCH BEFORE
UNPLUGGING THE MACHINE’S POWER CORD.
If you leave the treadmill plugged in after turning
off the console, there will still be current running
to the console. This treadmill is equipped with a
safety control program that will automatically shut
down the machine after six hours of no use. In the
event of an automatic shut down, please follow the
procedure below to restart the treadmill:
A. Unplug the power cord form the machine’s
socket.
Replug the power cord into the machines socket to
restart the machine.
MOVING AND STORAGE
After assembly is complete, you may fold the
treadmill into upright position for storage. To do
this, raise the deck until it locks into position.
NOTE! Make sure you hear the click sound of the
deck locking into position. This is to ensure the deck
is locked in place and will not drop back down.
NOTE! Make sure the treadmill’s incline is at 0 before
folding the deck. If the incline is not at 0, folding will
damage the mechanism.
NOTE! This machine has a built-in safety unfolding
feature to help the deck lower slowly. Please make
sure there are no children or other things under the
deck when you lower it.
TO MOVE THE TREADMILL
Before moving the Path, be sure the power cord is
unplugged from the wall and the treadmill. Fold
up the running deck until it is locked and push the
equipment on the transportation wheels. Lower
the treadmill carefully onto the floor. Hold the
handlebar to move forward the treadmill.
NOTE! Transport the treadmill with extreme caution
over uneven surfaces, for example over a step. The
treadmill should never be transported upstairs using
the wheels over the steps, instead it must be carried.
Power
cord
ON/OFF
Safety switch
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bremshey Treadline Tour at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bremshey Treadline Tour in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info