Manual Bremshey Sport TOUR (page 6 of 68) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

541850

Zoom out

Zoom in

1/68

OWNER'S MANUAL • PATH

OPERATION AND PROGRAMS

1. Insert the Safety key.

2. Press the POWER button. The monitor will turn on.

3. Select program with the SELECT button.

4. In the program PRO1 (Manual program), the

program window will display a track view. In the

program PRO2-8 (preset profile program), the

program window will display a profile view. Press

ENTER / SELECT to confirm your desired program.

5. In the programs PRO1 and PRO2-8, press +

/ - buttons to set up your desired time to do the

exercise. Press ENTER / SELECT to confirm your

setting value. Press START to begin. In the PRO1

program, set the incline and speed manually.

In PRO2-8, the incline and speed changes are

automatic. You can set the speed and incline of each

profile bar also manually during training.

MAINTENANCE

The equipment is safe to use only when periodically

maintained and inspected for faults and wear.

CAUTION! Do not attempt any servicing or

adjustment other than those described in this

manual. Any other servicing must be performed

by an authorized service representative. Check the

tightness of all fixing screws once a year. Do not

overtighten.

CLEANING AND LUBRICATING THE TREADMILL

FAILURE TO LUBRICATE YOUR TREADMILL MAY

INVALIDATE THE PRODUCT’S WARRANTY!

Wipe the treadmill surfaces, especially the

handlebars and console from dust with a damp

cloth or towel. Do not use solvents. Use a small

vacuum nozzle to carefully vacuum around all

visible components (belt, running deck, side rails

etc.). Also keep the area near the treadmill clean.

While in use, the treadmill gathers dust that may

cause problems in the operation of the equipment.

In average domestic use (a maximum of 60 minutes

a day), you should check the lubrication once a

month – however, lubricate the belt only if needed.

In more demanding use, the lubrication needs be

checked at shorter intervals. This is best done before

you begin a training session. Check the lubrication

as follows:

1. Ensure the treadmill is powered off! Step on

the treadmill belt .and stand steadily where you

normally run on the belt.

2. Take hold of the horizontal handlebar and push

the belt with your feet so that it slides back and

forth. The belt should move softly and evenly,

without a sound.

3. If you notice jerky movement or if the belt will

not slide check for lubrication by sliding your hand

under the belt.

Lubricate the running deck according to the

following instructions:

1. Attach the nozzle of the lubrication tube to the

T-Lube S container.

2. Lift the running deck and lock it.

3. Position the nozzle between the belt and the

board. Try to reach the spray as far into the center of

the running deck as possible.

4. Spray the lubricant for 2-3 seconds.

5. Lower the running deck into its normal position.

Use treadmill for your training session. Or allow the

treadmill to run for at least 5 minutes.

NOTE! Lubricate your treadmill only with T-Lube

S silicon lubricant. Contact your local Bremshey

distributor for further supplies of T-Lube or further

information on lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and make

adjustments as needed. The belt should run in the

center of the treadmill. Alignment is not usually

needed, provided

•

the treadmill is placed on an even, solid and

horizontal surface and the belt is correctly tensioned

•

the alignment of the belt is correct

It is, however, possible for the belt to be pushed to

one side due to the user’s running style (e.g. more

weight on one foot). The alignment of the belt is

adjusted by turning the two bolts at the back of the

treadmill.

ALIGN THE BELT ACCORDING TO THE FOLLOWING

INSTRUCTIONS:

Turn the power switch on and increase the

treadmill’s speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left

adjustment bolt 1/4 turn clockwise and the right

adjustment bolt 1/8 turn anti-clockwise. If the belt

drifts to the right, turn the right adjustment bolt 1/4

turn clockwise and the left adjustment bolt ¼ turn

anti-clockwise.

3. If the belt remains centered the adjustment is

correct. If not, continue to make small adjustments

as above until the belt is correctly aligned. If the belt

is allowed run across to one side for long periods of

time the edges of the belt may be damaged and the

treadmill may not continue to operate correctly. Any

damage to the belt caused by the lack of necessary

adjustment will not be covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on

the rollers. In normal use, however, keep the belt

as loose as possible! The belt tension is adjusted by

turning the same screws as used for aligning the

running belt. If turning the screws will not effect the

belt tension, please contact your local Bremshey

dealer.

1. Increase the treadmill’s speed to 5 km/h (3 mph).

2. Turn both adjustment screws an equal amount, ¼

turn clockwise.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bremshey Sport TOUR in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bremshey Sport TOUR Manual

Product: