517808

Breezair Icon Manual

16
Zoom out
Zoom in
Previous page
1/20
Next page
Seasonal maintenance is only
required if you have a cooler fitted
with a bleed system. The following
pages outline the maintenance
required at the end of the season and
then at the start of the next season.
This ensures that your cooler
continues to operate efficiently.
If your cooler is fitted with a drain
valve no seasonal maintenance is
required. However, we require that
the following components and the
operation thereof, be checked after
the first year, then every 2 years as
routine maintenance.
(1)...... Belt drive.
(2)...... Pump.
(3)...... Drain valve.
(4)...... Solenoid and associated
filter.
(5)...... Fan motor operation and
current.
(6)...... Float valve.
Routine maintenance may be
required more frequently in adverse
environmental situations and very
dusty areas.
Note
Failure to carry out regular
maintenance will affect your
warranty coverage.
!
WARNING
As your cooler is mounted on the
roof, we suggest that any
maintenance or checks be carried
out by an authorised Breezair
dealer or service agent. Climbing
onto the roof can be hazardous
and could result in injury to you
and damage to your property.
END OF SEASON
(1).. Turn off the water supply to
the cooler.
(2)...Remove the pad frames as
shown on page 17.
(3)...Turn off the power at the
isolating switch inside the
cooler.
(4)...Check and clean the water
distributing channels
under the lid.
(5)....Unclip and remove the
bleed system as shown
below. Take care not to
lose the o-ring. This
removal will allow the
water to drain from the
tank throughout the winter.
(6)....Thoroughly clean the tank
and the pump filter. Do
not replace the bleed
system. If you do, water
will sit without draining
from the tank throughout
the winter months.
(7).... Refit the pad frames.
HEALTH REGULATIONS
In some states, regulations require
that evaporative air coolers be
serviced at specific intervals.
1
ILL1141-A
2
1
®
16
Evaporative Cooler
PRE-SEASON
NOTE: Do
not wash the pads with
high pressure water spray.
WARNING:
Do not run the cooler with
the pad frames removed.
(1)...Turn your main switchboard
power off.
(2)...Remove the pad frames as
shown in the next column.
(3)...Ensure the power is off at
the isolating switch inside the
cooler.
(4)...Gently wash the pad frames
to remove any dust build up
during the winter.
If the pads are salted-up
replace them.
(5)...Replace the bleed system
that was removed at the end
of the last season. Ensure
that the o-ring is in place and
that the tray is positioned so
that it can catch the water
from the pad.
(6)...Turn on the water supply to
the cooler.
(7)...Check for water leaks.
Check operation of float
valve.
(8)...Check if adj. required to belt
drive. Reset motor amps.
(9)...Switch on the isolating
switch.
(10).Refit the pad frames.
(11).Turn the power on at your
main switchboard.
(12).Run the cooler.
REMOVING PAD FRAMES
To remove a pad frame:
(1)...Remove the clips holding the
pad frame in place.
(2)...Insert a flat head screw
driver into the slot between
the lid and the top of the pad
frame. Lever it so the pad
frame is released.
(3)...... Take hold of the pad frame,
pivot it outwards and lift it up. Be
careful not to damage the pad.
Repeat the steps above with the 3
remaining pad frames.
(For EXH210 units only) There are
90mm pads fitted to the front and rear,
with 100mm pads fitted to the sides
(facing the fan scroll holes). These
pads must be re fitted to their original
positions, or the larger pads could
catch on the float valve or components
mounted on the scroll.
The 100mm pads can be identified by
a rebate at the base of the Chillcel.
If fitted incorrectly, a drop in
performance may be found, water
can bypass the pad and be carried
over into the airstream and ducting
and/or damage to the pads or
electronic components may occur.
ILL950-C
1
2
3
ILL187-E
1
2
3
SEELEY INTERNATIONAL – OWNER’S MANUAL 17
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Breezair Icon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Breezair Icon in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info