517808
7
Zoom out
Zoom in
Previous page
1/20
Next page
AUTO MODE
The remote control contains a
thermostat. In AUTO mode the cooler
is controlled automatically, based on
your pre- comfort level. The
cooler will adjust the fan speed,
switch between COOL and VENT and
turn itself off. However, the sequence
and regularity at which these settings
change will differ with each operation
of the cooler.
As the remote control senses room
conditions, the
heat
from direct sunlight or electrical
appliances. Likewise placing the
remote control in cupboards or
drawers or under cooling vents will
affect the cooler’s operation.
To set the AUTO mode press the
button until AUTO is displayed.
Ten levels of comfort are available
with the remote control. While in
AUTO mode pressing the and
buttons will adjust the level of
required comfort. The display
selected
comfort control
settings will be influenced by
will
show your selection by indicating a
level between 1 and 10. WARMER or
COOLER will be displayed on the
screen as settings are changed.
AUTO TIMER MODE
AUTO TIMER mode can be
selected by using the button.
Once the AUTO TIMER mode is
selected the cooler will only
operate during the programmed
time period.
Programming the timer must be
performed before AUTO TIMER
can be activated. This can be done
while in any mode, even when it is
OFF. There are 7 steps involved in
setting the AUTO TIMER.
NOTE: After pressing the
button the display will revert back
to the previous setting if no buttons
are pressed within 4 seconds.
To program the timer use the
following sequence:
(1) Setting the ON time hour
Begin by pressing the
button. The hour displayed will
start flashing and the word ON will
appear on the screen. Then use
the and buttons to
change the hour value.
AUTO
TIMER
ON
ILL1112-A
AUTO
FAN
SPEED
ILL1105-A
PM
®
6
Evaporative Cooler
(2) Setting the ON time minutes
(3) Setting the OFF time hour
Press the button. The
minutes displayed will start
flashing and the word ON will
appear on the screen. Then use
the and buttons to
change the minute setting.
Press the button. The hour
displayed will start flashing and
OFF will be displayed. Then use
the and buttons to
change the hour.
Press the button. The
minutes displayed will start
flashing and the word OFF will
appear. Then use the
and buttons to change the
minute setting.
(4) Setting the OFF time minutes
AUTO
TIMER
ON
ILL1113-A
AUTO
TIMER
OFF
ILL1114-A
AUTO
TIMER
OFF
ILL1115-A
(5) Setting the comfort level
Press the button and the
comfort level number (1 to 10)
displayed will start flashing. Then use
the and buttons to change
this setting.
To select economy press the
button so that it is displayed on the
screen.
Now that you have programmed the
settings for AUTO TIMER they will be
stored in the remote control’s memory
until you change them. Press the
button until AUTO TIMER is
displayed on the screen. Your cooler
will now only operate during the
programmed time period.
NOTE: To change any AUTO TIMER
settings when the remote control is
switched off, the button needs to
be pressed and released within 1
second. To change settings when the
remote control is turned on press the
button until the desired number is
flashing.
(6) Setting ECONOMY
(7) Activating AUTO TIMER
AUTO
TIMER
ILL1116-A
SEELEY INTERNATIONAL OWNER’S MANUAL 7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Breezair Icon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Breezair Icon in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info