597307

Braun ThermoScan IRT 6510 Manual

5
Zoom out
Zoom in
Previous page
1/20
Next page
6 7
English
4
Fit the probe snuggly into the ear canal, then push
and release the Start button .
ExacTemp light will pulse while temperature is in progress.
The light will remain solid for 3 seconds to indicate that a
successful temperature reading has been achieved.
NOTE: If the probe has been properly inserted into the ear canal
during the measurement, a long beep will sound to signal the
completed measurement.
If the probe has NOT been constantly placed in a stable position in the
ear canal, a sequence of short beeps will sound, the ExacTemp light will
go out and the display will show an error message (POS = position error).
See
«
Errors and troubleshooting
»
section for more information
5
6
The confirmation beep indicates that an accurate
temperature measurement has been taken. The
result is shown on the display.
For the next measurement, press Eject button to
remove and discard used lens filter, and put on a new,
clean lens filter.
The Braun ThermoScan ear thermometer turns off
automatically after 60 seconds of inactivity.
The thermometer can also be turned off by
pressing the Power button .
The display will briefly flash OFF and it will go blank.
7
Temperature taking hints
Always replace disposable lens filters to maintain accuracy and hygiene. The right ear measurement may
differ from the measurement taken in the left ear. Therefore, always take the temperature in the same ear.
The ear must be free from obstructions or excess earwax build-up to take an accurate reading.
External factors may influence ear temperatures, including:
Factor Yes affects
Poor probe placement
Used lens filter
Dirty lens
In the cases below, wait 20 minutes prior to taking a temperature.
Factor Yes affects
Extreme hot and cold room temperature
Hearing aid
Lying on pillow
Use the untreated ear if ear drops or other ear medications have been placed in the ear canal.
Memory mode
2
1
3
4
This model stores the last
9 temperature measurements.
To display the stored
measurement, the
thermometer must be
turned on.
Press the Mem button.
The display shows the temperature, and when
releasing the Mem button, the stored temperature
for that memory number is displayed, together
with “M”.
Each time the Mem button is pushed, the stored
reading and an M is displayed to indicate each
temperature measurement (eg. M2).
Memory mode is automatically exited by not
pressing the memory button for 5 seconds.
The last temperature
taken is stored in the
memory and will be
automatically displayed
for 5 seconds when it is
turned on again.
Available only in
IRT 6510
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Braun ThermoScan IRT 6510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Braun ThermoScan IRT 6510 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info