790268
17
Zoom out
Zoom in
Previous page
1/104
Next page
17
Do not use abrasive cleaning agents. These may damage the device or scratch the
glass filter.
Do not attempt to use this device other than for removing unwanted hair.
Do not use the device on a surface other than skin. Do not press the treatment
button when the treatment window (1) is not placed in full contact with the skin.
Do not block the cooling vents. The device may overheat and pose an electric
shock risk or fire hazard.
How to use
Preparing the treatment area
Remove any visible hair on the skin before using the device. You may use your preferred hair removal
method. To keep the treatment window clean and intact, ensure there is no hair remaining on the skin
surface. Clean the treatment area and pat it dry.
To power on the device:
Use the mains cord (8) to connect the base station to an electrical outlet. Press any button (4 or 5) to
activate the device. The LED power bars (3) will light up once and a fan starts running. This means the
device is in READY mode. During operation, the device will heat up slightly.
Automatic light adaptation
When both skin tone sensors (2) have skin contact, the device reads your skin tone and selects the
appropriate light intensity which is indicated by white LEDs on the Power bars (3). These confirm that the
device is ready to flash.
light skin tone U high light intensity
dark skin tone U low light intensity with fast flash rate
no LEDs no skin contact U device will not flash
red LED invalid skin tone U device will not flash
Gentle mode
Push the gentle mode button (4) to reduce the light intensity. You can toggle through the following 3
settings:
Standard: 3 indicator lights
Gentle: 2 indicator lights
Extra gentle: 1 indicator light (lowest light intensity with fast flash rate)
Gentle and extra gentle settings are intended for sensitive areas and first time users. With reduced light
intensity, more treatments may be required to see the desired effects.
The power bars flash to confirm a change in the light intensity setting.
When holding the gentle mode button (4) longer than 3 seconds, the device is deactivated.
After 10 minutes without use, the device is automatically deactivated.
Press any button to re-activate it.
Patch Test
Before your first treatment, we recommend you test your skin for reaction to Braun Silk·expert on a small
area of skin of the body part you plan to treat (about 2 x 3 cm in size; equivalent to the size of two flashes,
side by side).
Perform a patch test as described below in chapter «Treatment methods», section «STAMPING».
Wait 48 hours to examine the test area. If the skin appears normal, begin your first treatment. If a skin
reaction develops, discontinue using the device and consult your physician.
91840600_Victoria2_PL5_Euro1.indd 1791840600_Victoria2_PL5_Euro1.indd 17 13.01.21 10:0413.01.21 10:04
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Braun Silk-expert Pro 5 PL5267 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Braun Silk-expert Pro 5 PL5267 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info