Manual Braun si 6210 freestyle (page 5 of 22) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

323026

Zoom out

Zoom in

1/22

English

Our products are engineered to meet the

highest standards of quality, functionality and

design. We hope you enjoy your new Braun

FreeStyle.

Notice: Remove the sole plate label, if any,

before first use.

–––––––––––––––––––––––––––––––––––––––––

Important safeguards

•

Before using the iron, read the use instruc-

tions completely. Keep the use instructions

during the entire life of the iron.

•

Make sure your voltage corresponds to the

voltage printed on the iron. Connect the

iron to alternating current only.

•

Always unplug the iron before filling with

water and make sure the steam button is

in its lower position (steam off). Always pull

the plug, not the cord. The cord should

never come in contact with hot objects or

with the hot sole plate.

•

Never immerse the iron in water or other

liquids.

•

During ironing pauses, always place the

iron upright on its heel rest. Unplug it when

leaving the room, even if only for a short

time.

•

Never pull out the steam button (3) during

ironing.

•

Keep the iron away from children.

Electric irons combine high temperatures

and hot steam that could lead to burns.

•

Check the cord regularly for possible

damage.

•

If the appliance (including cord) shows any

defect, stop using it and take it to a Braun

Service Centre for repair.

•

Faulty or unqualified repair work may

cause accidents or injury to the user.

–––––––––––––––––––––––––––––––––––––––––

A Description

1 Spray nozzle

2 Water tank opening

3 Steam button

3a Steam regulator

4 Spray button

5 Power shot button

6 Temperature selector

7 Temperature pilot light

B Before starting off

•

This iron is designed for tap water. If you

have extremely hard water, we recommend

to use a mixture of 50% tap water and

50% distilled water. Fill the water tank to

«max» marking. Never use distilled water

exclusively. Do not add any additives

(e.g. starch).

•

Keep the iron in the upright position and

connect it to the mains. Select the tem-

perature according to the ironing guide on

the heel rest of the iron or on the label in

your garments.

•

The temperature pilot light (7) goes off,

when the desired temperature is reached

(after approx. 1 minute).

C Ironing

1 Steam on/off

For steam ironing, the temperature selector

(6) must be set within the red range.

Press the steam button (3) to start the

steam mode.

steam on steam off

With the steam button in its upper position,

turn

the steam regulator (3a) to adjust the

steam quantity.

Preconditioning

(not with models SI 6210, SI 6510)

Steam develops also horizontally at the

front area of the sole plate. This pre-

conditions the textiles by «pre-steaming»,

thus making ironing easier.

Be careful – steam comes out laterally.

2 Power shot

Prior to use, press the power shot button

(5) 3 to 4 times to activate it. Press the

power shot button in intervals of at least

5 seconds.

Power shot can be activated when dry

ironing. However, the temperature selector

has to be set in the range between «•••»

and «max». The power shot function can

also be used in the vertical position for

steaming hanging clothes.

3 Spray function

Press the spray button (4).

4 Dry ironing

Turn the steam mode off by pressing the

steam button (3) so that it catches in the

lower position.

D After ironing

•

Unplug the iron and press the steam on/off

button (3) so that it catches in its lower

position (steam off).

•

To prolong the life of the iron, empty the

water tank.

•

Store the cool iron in a dry place always

standing on its heel rest.

E Maintenance and cleaning

To clean the sole plate, use steel wool.

Then wipe the sole plate clean with a cloth.

Never use a scouring pad, vinegar nor

other chemicals. To clean the soft material

of handle and power shot and spray

buttons, use soapy water.

F Cleaning the anticalc valve

The iron’s anticalc valve is located at the

lower end of the steam button (3). It has

to be decalcified regularly (e.g. when the

steam development is insufficient).

Proceed as follows:

1) Unplug the iron and empty the water tank.

2) Press the steam button so it is lifted.

3) Remove carefully (some water may now

leak from the sole plate).

4) Do not touch the anit-calc valve.

5) Immerse in vinegar (not vinegar essence)

or lemon juice until the lime becomes soft.

6) Use a non-metallic brush until all openings

are clean.

7) Rinse under running water.

8) Re-insert the steam button.

9) Press to check the steam on/off function.

Note:

the iron must never be used without

the steam button.

G Decalcifying/ anticalc system

When scale particles come out of the

steam vents or when the steam

development is insufficient even after

cleaning the anticalc valve, you should

clean the steam chamber as follows:

1) Make sure the steam button is in its lower

position.

2)–3) Fill water into the tank, connect to the

mains and select the «•••» temperature

setting.

4)–5) Wait until the pilot light turns off.

Unplug the iron.

6)–7) Hold the iron over a sink, then press the

steam button so it is lifted, carefully pull it

up, turn it and rest it in this position.

Caution:

When the steam button is pulled

up, hot water and steam will come out from

the sole plate.

8) Push back the steam button until it catches

in the lower position.

9)–10) Fill water into the tank, connect to the

mains and select the «•••» temperature

setting.

11)–13) When the pilot light goes off, press

the power shot button 4 times to rinse the

iron. Disconnect the iron and wait for the

sole plate to cool off, then clean it as

described above in section E.

Note:

the iron must never be used without

the steam button.

H Trouble-shooting guide

Problem Remedy

––––––––––––––––––––––––––––––––––––––

Drops Turn the steam regulator

coming out anti-clockwise to reduce

of the steam the steam or press the

vents steam button to turn the

steam off.

Take longer intervals

when pressing the power

shot button.

Select a higher tempera-

ture setting.

No steam Press the steam button

at all so that it is lifted.

Less steam Clean the anticalc valve

develops or no (see F).

steam at all

Calcium Decalcify the steam

particles chamber (see G).

coming through

the steam vents

––––––––––––––––––––––––––––––––––––––

Subject to change without notice.

This product conforms to the

EMC-Requirements as laid down

by the Council Directive 89/336/EEC

and to the Low Voltage Regulation

(73/23 EEC).

press

4699350_SI 6530_MN Seite 5 Freitag, 27. April 2001 12:03 12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Braun si 6210 freestyle in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Braun si 6210 freestyle Manual

Product: