Manual Braun series 5 590cc 3 (page 12 of 62) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

369968

Zoom out

Zoom in

1/62

When cleaning is finished, the yellow

cleaning light will go off and the shaver is

ready for use.

A cleaning cartridge should be sufficient for

about 30 cleaning cycles. When the level

indicator (1) has reached the «min» mark,

the remaining fluid in the cartridge is

sufficient for about 5 more cycles. Then the

cartridge should be replaced, when used

daily approx. every 4 weeks.

The hygienic cleaning cartridge contains

alcohol, which once opened will naturally

evaporate slowly into the surrounding air.

Each cartridge, if not daily used, should be

replaced after approximately 8 weeks.

The cleaning cartridge also contains

lubricates, which may leave residual marks

on the shaver head after cleaning.

However, these marks can be removed

easily by wiping gently with a cloth or soft

tissue paper.

Cleaning the housing

From time to time clean the housing of the

shaver and the Clean&Renew station with a

damp cloth, especially inside the cleaning

chamber where the shaver rests.

Replacing the cleaning cartridge

After having pressed the lift button (2) to

open the housing, wait for a few seconds

before removing the used cartridge to avoid

any dripping.

Before discarding the used cartridge, make

sure to close the openings using the lid of the

new cartridge, since the used cartridge will

contain contaminated cleaning solution.

D Manual cleaning

The shaver head is suitable for

cleaning under running tap water.

Warning: Detach the shaver from the

power supply before cleaning the

shaver head in water.

Rinsing the shaver head under running water

is an alternative way to keep the shaver

clean, especially when traveling:

•

Switch the shaver on (cordless) and rinse

the shaver head under hot running water.

You may use liquid soap without abrasive

substances. Rinse off all foam and let the

shaver run for a few more seconds.

Next, switch off the shaver, press the foil

release buttons (9) to remove the shaver

foil (7) and cutter block (8). Then leave the

disassembled shaving parts to dry.

If you regularly clean the shaver under

water, then once a week apply a drop of

light machine oil onto the long hair trimmer

(10) and shaver foil (7).

The following quick cleaning is another

alternative cleaning method:

Press the foil release buttons (9) to lift

the shaver foil (do not remove the foil

completely). Switch on the shaver for

approx. 5–10 seconds so that the shaved

stubbles can fall out.

Switch off the shaver. Remove the shaver

foil and tap it out on a flat surface. Using

a brush, clean the inner area of the shaver

head. However, do not clean the shaver foil

nor the cutter block with the brush as this

will damage them.

Keeping your shaver in top

shape

Replacing the foil and cutter block / reset

To maintain 100% shaving performance,

replace the shaver foil (7) and cutter block (8),

when the replacement symbol (16) lights up

(after about 18 months) or when cassette is

worn.

The replacement symbol will remind you

during the next 7 shaves to replace the

shaver foil and cutter block. Then the shaver

will automatically reset the display.

After you have replaced the shaving parts (foil

and cutter block), press the on/off switch (13)

for at least 5 seconds to reset the counter.

While doing so, the replacement light blinks

and goes off when the reset is complete.

The manual reset can be done at any time.

•

99503077_590_MN_Gift_S6-64.indd 1299503077_590_MN_Gift_S6-64.indd 12 14.04.2010 13:34:33 Uhr14.04.2010 13:34:33 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Braun series 5 590cc 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Braun series 5 590cc 3 Manual

Product: