Manual Braun PRO 4000 (page 6 of 21) (English, French, Spanish)

101281

Zoom out

Zoom in

1/21

If the thermometer shows «RET» (without the battery symbol) on its display, the

anti-theft time has elapsed and the thermometer must be returned to the station

for unlocking.

If the anti-theft function is not enabled, the display will show «off» when in stand-

by mode.

Care and cleaning

Braun ThermoScan probe covers are intended for single use only!

To ensure accurate readings, always use Braun ThermoScan disposable probe

covers with the PRO 4000 thermometer. Damaged, perforated, or soiled probe

covers can lead to inaccurate temperature readings. Additionally, the accuracy of

your temperature readings can be affected by damage to the probe window, or

the presence of dirt or cerumen on the probe window.

To assure a high level of accuracy, it is very important to keep this window clean,

dry and undamaged. Fingerprints, cerumen, dust and other soiling compounds

reduce transparency of the window and result in lower temperature measure-

ments. If the thermometer is accidentally placed in the ear without a probe cover

installed, the window must be cleaned immediately. Additionally, the window

and/or probe tip area should never be modied, changed, or adjusted. These

changes will affect calibration and accuracy of the thermometer.

To clean the window, gently wipe its surface with a cotton swab slightly moist-

ened with isopropyl alcohol and immediately wipe dry with a clean cotton swab.

After cleaning, allow at least 5 minutes drying time before taking temperatures.

Make sure probe window is clean and dry. Avoid touching the window except

when cleaning is required. If the window is damaged, the thermometer must be

returned to Welch Allyn for service.

Note: Do not use any chemical other than isopropyl alcohol to clean the probe

window.

Thermometer

Use a soft cloth slightly moistened with isopropyl alcohol to clean the thermome-

ter display and exterior. As needed, clean the thermometer and probe with a 70%

isopropyl alcohol solution or a 10% chlorine bleach solution or a nonstaining

disinfectant such as CaviCide

or its equivalent. Do not use abrasive cleaners.

Never submerge the thermometer in water or any other liquid. Store thermometer

and probe covers in a dry location (the thermometer is not protected against in-

gress of water), free from dust and contamination and away from direct sunlight.

The ambient temperature at the storage location should remain fairly constant

and within the range of 50 °F to 104 °F (10 °C to 40 °C).

Trouble-shooting

Situation Solution

Error message

No probe cover is attached. Attach new, clean probe cover.

(POS = position error)

The infrared monitor cannot nd a

temperature equilibrium and allows

no measurement.

Clear the display by changing

the probe cover.

Ensure that the positioning of the

probe is correct and remains stable.

(ashing)

Ambient temperature is not within the

allowed operating range 50–104 °F

(10–40 °C) or changing too rapidly.

Allow the thermometer to remain for 30

minutes in a room where the tempera-

ture is between 50 and 104 °F / 10 and

40 °C.

Temperature taken is not within typical

human temperature range.

HI will be displayed when temperature

is higher than 108 °F (42.2 °C)

LO will be displayed when temperature

is lower than 68 °F (20 °C)

Make sure a new, clean probe cover is

attached and thermometer is properly

inserted. Then, take a new temperature

System error

If error persists,

If error still persists,

Wait 1 minute until the thermometer

turns off automatically, then turn on

again.

... reset the thermometer by removing

the batteries and putting them back

in.

... contact Welch Allyn.

10 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Braun PRO 4000 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Braun PRO 4000

Braun PRO 4000 User Manual - Dutch, Danish, Polish, Swedish, Norwegian, Finnish - 69 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Braun PRO 4000 Manual

Product: