Manual Brandt TE1074X (page 18 of 20) (English, French)

487532

Zoom out

Zoom in

1/20

make reference to the legislation, in conformity

with the local regulations.

FOR THE U.K. ONLY

The room containing this hotplate should have an

air supply in accordance with BS 5440: Part 2:

1989.

All rooms require an openable window, or -

equivalent and some rooms will require a

permanent vent a well.

For room volumes up to 5 m -

an air vent of 100cm

is required.

For room volumes between 5 m -

and 10 m

an air

vent of 50 cm

is required.

If the room is greater than 5 m -

and has a door that

opens directly to the outside, then no air vent is

required.

If there are other fuel burning appliances in the

same room BS 5440: Part 2:1989 should be

consulted to determine the air vent requirements.

Gas connection

Make sure that the appliance is adjusted for

the gas type available (see the label under the

appliance). Follow the instructions indicated in the

chapter “gas transformations and adjustments”

for the possible

adaptation to

different gases.

The appliance

m u s t b e

connected to

the gas system

by means of stiff

metal pipes or

flexible steel pipes having continuous walls, in

compliance with the regulations in force.

Some models are equipped with both cylindrical A

and conical B connectors for gas supply (fig. 7).

Please select the type which is correct for the

supply concerned.

The connection must not stress the gas ramp.

Once the installation is over, check the

connection seal with a soapy solution.

Electric connection

The connection to the electric grid must be carried

out by qualified personnel and in conformity with

the regulations in force.

The voltage of the electric system must correspond

to the value indicated in the label under the

appliance. Make sure that the electric system is

provided with an effective ground connction in

compliance with the regulations and provisions of

the law. Grounding is compulsory.

If the appliance is not equipped with a plug, apply

a standardized plug to the power supply cable.

This device must be at a suitable opening distance

from the contacts in order to allow the entire

disconnection in case of overvoltage category III,

in accordance with installation rules.

GAS TRANSFORMATIONS AND ADJUSTMENTS

Replacing the nozzles

If the equipment is adjusted for a type of gas that is

different from the one available, it is necessary to

replace the burner nozzles.

The choice of the nozzles to replace must be

made according to the table of the “technical

characteristics” as enclosed.

Act as follows:

Remove the racks -

and burners.

By means of a -

straight spanner L, unscrew

the nozzle U (fig.8) and

substitute it with the

corresponding one.

Tighten the nozzle -

strongly.

Adjusting the burners

The lowest flame point must always be properly

adjusted and the flame must remain on even if

there is an abrupt shift from the maximum to the

minimum position.

If this is not so, it is necessary to adjust the lowest

flame point as follows:

start the burner up; -

turn the tap up to the minimum position (small -

flame);

remove the knob from the tap rod; -

introduce a flat-tip screwdriver C in the hole of -

control panel of the tap (fig. 9) and turn the by-

pass screw V (fig.9/A) up to a proper adjustment

of the lowest flame point.

Fig.9 Fig.9/A

As regards G30 gas burners, the by-pass screw

must be tightened completely.

INSTRUCTIONS FOR THE INSTALLER

Fig.7

Fig.8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brandt TE1074X in the language / languages: English, French as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brandt TE1074X Manual

Product: