737224
43
Zoom out
Zoom in
Previous page
1/52
Next page
Assembly / Owner’s Manual
43
Condition/Problem Things to Check Solution
Unit will not power up/turn on/start Outlet Make sure outlet is functioning correctly. Verify this by plugging another
device (ex: lamp) into the outlet. If outlet is connected to a light switch,
check to make sure it is on. If outlet is not functioning nd a working
outlet.
Power cord not plugged in Make sure the power cord is rmly secured to A/C inlet on the unit and
rmly inserted into a non-GFI wall socket.
Power switch turned off Make sure the power switch at the rear of the unit is in the “ON” posi-
tion. Switch will light up red to indicate power is present.
Safety key not plugged in Plug Safety Key into Console (See Safety Key (Emergency Stop Procedures)
within Features section).
Speed displayed is not accurate Display set to wrong unit of mea-
sure. (English/Metric)
Change display units.
Walking belt misalignment Rear belt guides Belts should ride on top of triangular black belt guides at rear of
treadles.
Tracking adjustment Belts are not required to be perfectly centered and are typically farther
out in the rear than they are in the front. This may vary depending on
user’s stride. If belt is tracking to one side far enough to cause rubbing
of belt, consult the “Adjusting the Walking Belts” procedure.
Speed dependent grinding or
scraping noise
Belt alignment Check walking belt alignment. Belt contact with metal guides under
Treadle can make a loud grinding sound. If belts are misaligned, adjust
walking belt.
Rollers or motor Contact your local Bowex
®
distributor for further assistance.
Hesitation or belt slipping when
walking on unit
Walking belt tension Adjust walking belt tension by following the “Adjusting the Walking Belt”
procedure.
Knocking noises when unit is
operating
Igus bushing If knocking sound seems to be coming directly from the rear roller,
check Igus (yellow “hat” shaped) bushings and replace if cracked.
Hydraulic cylinder bolts Check and tighten both upper and lower bolts that connect the hydraulic
cylinders to the unit.
Belts stop turning while in use Safety key Plug Safety Key into Console (See Safety Key (Emergency Stop Procedures)
in Features section).
Motor overload Unit may be overloaded and drawing too much current, causing unit
to shut power down to protect motor. Consult belt lubrication schedule
to determine if belts need lubrication, check walking belt tension, and
restart unit.
Outlet Outlet may not have enough power available for the machine due to
other devices on same circuit. Remove any devices from power circuit
and restart machine.
Console displays “C”, “S”, or “H”
with a number
Unit needs to be restarted Cycle power off for 10 seconds using power switch at rear of unit, then
restart.
Error code diagnostic Contact your local Bowex
®
distributor for further assistance.
Console displays “LUbE” code Belt lubrication Consult lubrication schedule and apply if necessary. Push START but-
ton.
Troubleshooting
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bowflex TC10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bowflex TC10 in the language / languages: English as an attachment in your email.

The manual is 11,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info