581997

Bowers en Wilkins M1 mk2 Manual

5
Zoom out
Zoom in
Previous page
1/6
Next page
ENGLISH
4 Connecting using the table stand
Remove the rubber mat from the underside of the
base (Figure 15).
Strip back the outer sheath of the cable by 75mm
(3 in) to expose the two inner sheathed wires.
Strip back the positive and negative wires to expose
10mm (3/8 in) of bare wire. If using multi-strand wire,
twist the strands to obtain a neat end.
Feed each wire through the appropriate hole in the
back of the base, observing the polarity coding
as indicated. The wires will follow a channel and
emerge in line with the side holes in the spring
terminals.
Press the ends of the terminals fully and push the
wire into the terminals. Then release the terminal
ends to clamp the wire.
Replace the rubber mat.
5 Fitting and connecting using the
wall bracket
WARNING!
Do not attach the speaker to the ceiling. Decide how
the cable is to be routed to the wall bracket – on the
wall surface (from underneath only), chased into the
plasterwork, or inside hollow (drywall) construction.
If routing the cable inside the wall or in the plaster
layer, install it before xing the wall bracket in place
and leave 50mm (2 in) showing with the outer sheath
stripped back.
Take care to route the cable clear of where the
bracket xing screws will be. For example, if the
cable is chased into the plaster from above, omit the
centre xing screw.
If laying the cable on the wall surface,t the wall
bracket rst. Cable cannot be routed around the
support platform of the bracket when the cover is
in place. There is only one knock-out in the cover
as shown, so the cable must approach from this
direction.
Using a spirit level, offer the wall bracket to the wall
and mark out thexing holes.
Drill and plug the wall as appropriate to the type of
construction (screws and plugs not supplied).
If laying the cable on the wall surface from below,
remove the knock-out at the bottom of the bracket
cover to accommodate the cable.
Strip back the ends of the inner cores of the cable
to expose 10mm (3/8 in) of bare wire and neatly
twist if multi-strand. Connect the wires to the screw
terminals, observing the correct polarity as shown.
Remove the table stand base, following the
instructions in Section 3.1.
Slide the cover up the stem. Make sure the securing
clamp is clear of the stem aperture in the bracket
and push the end of the speaker stem fully into
the aperture. Tighten the two screws through the
securing clamp evenly using the Torx key supplied
until the slack is taken out of the t of the stem.
Check that the tapered ridge of the clamp engages
the groove in the stem. Do not over-tighten.
Slide the cover back down the stem and click into
place on the wall bracket.
5
Figure 15
Figure 16
+
+
+
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bowers en Wilkins M1 mk2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bowers en Wilkins M1 mk2 in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info