741671

Boston Acoustics SoundWare Sub Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
6
Audio Signal Input
The audio signal from the system goes in to the Line In connector on the SoundWare Sub amplier panel. In some systems
that signal will come from a surround sound processor or an A/V receiver that has a dedicated subwoofer or LFE output. In
other systems the signal will come from the preamp output of a conventional stereo component.
Connecting to the Subwoofer or LFE Output of Surround Sound Processor or A/V Receiver: Digital 5.1, 6.1 and 7.1
hometheaterreceiversandsurroundprocessorshaveonechannel(the“.1”)thatprovidesaspeciallow-frequency(LFE)signal
contained in digitally-encoded soundtracks. Dolby® Pro Logic® receivers, and some stereo receivers, have a similar output.
Use a single RCA cable (not supplied), as shown, to connect your digital receiver’s LFE subwoofer output to the SoundWare
Sub Line In connector.
The signal from a subwoofer or LFE output has been ltered so it contains only very low frequency sound. The crossover in
the SoundWare Sub is not needed. Turn the Crossover control all the way up to the 180 Hz position.
In this type of system the audio adjustments are controlled by the receiver or sound processor. Usually these adjustments are
made with on-screen menus. Some of the adjustments you should set include:
Subwoofer On/O - Be sure the subwoofer output is turned on.
Crossover Frequency-Seethe“InitialControlSettings”sectionthatfollows.
Subwoofer Volume - Set this to the mid-point of the control range. Then use the SoundWare Sub volume control to
make nal adjustments. If you cannot get enough bass from the Sub, adjust this control to a higher setting.
Some receivers or sound processors may have other controls. Consult your receiver instruction manual for additional
information.
Connecting to Preamp Outputs – If the electronics in your system does not have a subwoofer or LFE output you can
connect the SoundWare Sub to a preamp output. You’ll need a Y-adapter (not supplied) to combine the left and right preamp
outputs. Connect a single RCA cable (not supplied) from the Y-adapter to the Line In of the Sub.
receiver or sound processor
receiver or amplifer
Preamp Out
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boston Acoustics SoundWare Sub at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boston Acoustics SoundWare Sub in the language / languages: English, German, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info