741674
15
Zoom out
Zoom in
Previous page
1/21
Next page
– 15
All Installations
1. Strip 1/2-inch (12mm) of insulation
from the wire, and twist the wire
strands together. The T2 speaker
jack will accept either bare wire (up
to 12-gauge) or single banana
plugs.
2. Connect the wire to the speaker,
being careful to retain proper
polarity.
3. Slide the speaker into the cutout
(see diagram #6).
4. Tighten the four Phillips mounting
screws. The mounting arms will
pivot into position and clamp the
speaker to the mounting surface
(see diagram #7).
NOTE
The tweeter island can be rotated 180
degrees, allowing you to redirect the
null without loosening the entire
speaker to reposition the tweeter
island.
WARNING
Do NOT overtighten the mounting
screws.
Todas las instalaciones
1. Pele 12 mm (1/2pulgada) de ais-
lante del cable y gire el cable para
unir los hilos. El conector del
altavoz T2 acepta tanto el cable
pelado (hasta un calibre 12) como
un enchufe sencillo con punta
cónica.
2. Conecte el cable al altavoz con
cuidado de mantener la polaridad
correcta.
3. Deslice el altavoz hacia el recorte
(consulte el croquis nº 6).
4.
Apriete los cuatro tornillos de
soporte Phillips. Los brazos de
soporte pivotarán en su posición
y sujetarán el altavoz a la superfi-
cie de instalación (consulte el cro-
quis nº 7).
NOTA
La isla del altavoz de agudos puede
girarse 180 grados, lo que le permite
redirigir el nulo sin necesidad de soltar
todo el altavoz para recolocar la isla del
altavoz de agudos.
ADVERTENCIA
No apriete excesivamente los tornillos
de soporte.
Toutes installations
1. Dénudez 12 mm (1/2") du câble et
torsadez les brins. Le réceptacle de
l’enceinte T2 accepte des câbles
dénudés (jusqu’au calibre 12) ou
des fiches « banane ». simples.
2. Connectez les câbles à l’enceinte en
observant de maintenir la polarité
correcte.
3. Glissez l’enceinte dans la cavité
découpée (voir diagramme 6).
4. Serrez les quatre vis Phillips de
montage. Les bras de montage piv-
oteront en position et ancreront
l’enceinte à la surface de montage
(voir diagramme 7).
REMARQUE
L’îlot des tweeter peut être pivoté sur
180 degrés, ce qui vous permettra de
diriger le « zéro » sans avoir à démon-
ter l’enceinte complète pour atteindre
l’îlot des tweeters.
AVERTISSEMENT
NE JAMAIS serrer excessivement les vis
de montage.
Alle Installationen
1. 12 mm Kabelmantel entfernen und
die Aderenden verdrillen. Der
Anschluss an die T2-Speaker-Buchse
kann mit blankem Draht (bis 12-
gauge, etwa 2 mm) oder einem
einzelnen Bananenstecker ausge-
führt werden.
2. Das Kabel an den Lautsprecher
anschließen, dabei auf die richtige
Polarität achten.
3. Den Lautsprecher in die Einbau-
öffnung einsetzen (siehe Abb. 6).
4. Die vier Kreuzschlitzschrauben
anziehen. Die Einbaubügel klap-
pen in Position und klemmen den
Lautsprecher an der Einbaufläche
fest (siehe Abb. 7).
ANMERKUNG
Die Tweeter-Insel kann um 180° gedreht
werden, wodurch die Null-Achse neu
ausgerichtet wird, ohne den gesamten
Lautsprecher zur Neupositionierung der
Tweeter-Insel lösen zu müssen.
ACHTUNG
Die Befestigungsschrauben nicht zu
fest anziehen.
Diagram #6
Diagram #7
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boston Acoustics HSi 470T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boston Acoustics HSi 470T2 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info