721946

Bostitch SC50HPB-E Manual

6
Zoom out
Zoom in
Previous page
1/39
Next page
GB
LOADING THE TOOL
1. Slide the fasteners onto the magazine rail (Fig 2A)
towards the front of the magazine (Fig 2B)
2. Pull back the pusher past the fasteners (Fig 3)
3. Gently release the pusher, so that it remains behind the
fasteners, pushng them along the magazine (Fig 4)
Note: Use only fasteners recommended by
Bostitch for use in Bostitch tools or fasteners which
meet Bostitch specifications.
TOOL OPERATION
1. The operator of the tool should understand that the
success of operating this tool depends on the method
(or technique) that the handles are operated. The
single most important issue will be in the outward
movement of the handles during the ring loading
cycle. The handles must be opened completely to
the full open position. This will need to be done in a
continuous motion to prevent the tool from jamming.
Failure to do this will cause the ring to feed short of
the latch nose.
The ring must feed beyond the latch nose to allow the
latch to position behind the ring and prevent the ring
from deforming during closure.
2. Any outward movement of the handles must result in
the full ring loading cycle. Partial outward movement
will push a ring only part way forward. When the
handles are returned to the start position and then
opened again the ring being fed on the second cycle
will jam into the previously incompletely cycled ring.
This ring jamming will cause the tool to jam and
lock the handles. If the handles become locked the
operator will need to remove the jammed rings from
between the jaws. This can be accomplished in the
following ways:
• Most of the time this can be accomplished by using
a screwdriver or other probing device to free the
jammed ring(s).
• If using the probe doesn’t remove the rings, than the
following will be necessary. Remove all rings from
the magazine.
Place the ring pusher in the parked position. This is
a point at the rear of the spring spool bracket. Just
hook the pusher in the slot near the bottom rear of the
bracket. Loosen both pivot bolt nuts 4 – 6 turns, this
will allow more clearance between the jammed rings
and the magazine. This should now allow the removal
of the jammed ring(s).
• In the event the above still doesn’t allow the removal
of the jammed ring(s) then it will be necessary to
remove the magazine completely. When re-installing
the pivot bolts or tightening the pivot bolt nuts, care
must be taken not to overtighten the nuts.
m This tool is intended to be used for fixing wire to wire
in automotive, mattress assembly and cage/wire assembly
or for closures in packaging etc. DO NOT USE for fastening
unsuitable materials which could cause buckling of the
fasteners and damage to the tool. If you are unsure of the
suitability of this tool for certain applicartions, please
contact your local sales oce.
m
WARNING! MOVEABLE PARTS & JAW (FIG 1)
•
These tools feature moveable parts including the jaw to
close the fasteners. Make sure only the material to be
fastened is placed within the jaws of this tool to avoid
the danger of crushing of fingers. Keeps hands clear at
all times to prevent serious injury.
m Warning!
•
IMPORTANT SAFETY INFORMATION ENCLOSED.
•
READ THIS MANUAL BEFORE OPERATING THE TOOL.
•
SAVE FOR FUTURE REFERENCE.
•
FAILURE TO OBSERVE THE FOLLOWING
WARNINGS COULD RESULT IN INJURY.
•
Keep body stance balanced and firm.
Do not overreach when operating this tool.
•
Use protective equipment such as
glasses, gloves, safety shoes as well
as acoustic protection. Remain vigilant,
use common sense and pay attention
when using the machine.
•
Always wear suitable CE marked
eye protection when operating or
performing maintenance on this tool.
© BOSTITCH 2019
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bostitch SC50HPB-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch SC50HPB-E in the language / languages: All languages as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info