721840

Bostitch RC-10-U110 Manual

10
Zoom out
Zoom in
Previous page
1/118
Next page
To avoid overheating of the electric motor, this compressor is designed for intermittent operation as indicated on the
technical dataplate (for example, S3-25 means 2.5 minutes ON, 7.5 minutes OFF).
SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS OF THIS TOOL!
OPERATION AND MAINTENANCE
NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and
maintenance of the compressor. Some illustrations in this Instruction Manual may show details or attachments that
differ from those on your own compressor.
INSTALLATION
Remove the compressor from its packing, makes sure it is in perfect condition, checking if it was damaged during
transport, and carry out the following operations:
Fit the wheels and rubber tab on the tanks on which they are not already fitted, observing the instructions in (fig.1a &
1b). Also fit the Air Filter (Fig 2). Position the compressor on a flat surface or with a maximum permissible inclination of
10°, in a well aired place, protected against atmospheric agents and not in a place subject to explosion hazard. If the
surface is inclined and smooth, check if the compressor moves while in operation - if it does, secure the wheels with
two wedges. If the surface is a bracket or a shelf top, make sure it cannot fall, securing it in a suitable way. To ensure
good ventilation and efficient cooling, the compressor must be at least 100 cm from any wall. Compressors fitted on
the tank, with fixed feet, should not be rigidly secured to the ground. In this case, we advise you to fit 4 anti-vibration
supports. Verify that the tanks have been drained and are clear of any moisture or dirt.
INSTRUCTIONS FOR USE
-Take care to transport the compressor correctly, do not overturn it or lift it with hooks or ropes. Check oil level,
consulting the reference marks on the stick (fig. 3).
Oil lubricated compressors may come with a bottle of oil to fill or top up the compressors - note that not all oil supplied
may be needed to fill the unit to the correct level.
NOTE: Some units (MRC6, RC-10) are equipped with an oil-free pump. There is no oil to replace or check.
ELECTRICAL CONNECTION
Single-phase compressors are supplied with an electrical cable and a two-pole & earth plug. The compressor must be
connected to a grounded power socket (fig.4).
IMPORTANT: Never use the ground socket instead of the neutral wire. The ground connection must be made to meet
safety standards (EN 60204). The plug of the power cable must not be used as a switch, but must be fitted in a power
socket controlled by a suitable differential switch (thermalbreaker).
STARTING
Check that the mains power matches that indicated on the electrical data-plate (fig.5) - the permissible tolerance range
is +/-5%. Turn or press into position “0” (according to the type of pressure switch fitted on the appliance) the knob
located on the upper section (fig. 6A, 6B, 6C). Fit the plug in the power socket and start the compressor, turning the
pressure switch knob into position “I”.
The compressor is fully automatic, and is controlled by the pressure switch which stops it when tank pressure
reaches maximum value and restarts it when it falls to minimum value. The pressure difference between maximum and
minimum values is usually about 2 bar (29 psi). E.g.: the compressor stops when it reaches 8 bar (116 psi - maximum
operating pressure) and restarts automatically when the pressure inside the tank drops to 6 bar (87 psi). After
connecting the compressor to the power line, load it to maximum pressure and check exactly how the machine is
operating.
NOTE: The head/cylinder/delivery tube unit can reach high temperatures. Take care when working near these parts,
and do not touch them to avoid possible burns.
IMPORTANT
The electro-compressors must be connected to a power socket protected by a suitable differential switch
(thermal-breaker). The motor is equipped with an automatic thermal breaker located inside the winding - this stops
the compressor when motor temperature reaches excessively high values (180
o
C). If the breaker is tripped, the
compressors restart automatically after 10 to 15 minutes.
© Stanley Bostitch
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bostitch RC-10-U110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch RC-10-U110 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info