Manual Bostitch MIIIFN (page 7 of 68) (All languages)

721916

Zoom out

Zoom in

1/68

2. Put the rubber cap slightly inclined on top of the steel stud, push downward with a twisting motion to engage

the rubber cavity over the edge of the steel stud.

3. Once fully engaged over the edge, you can release the mallet from the vise and hit it on solid surface to

properly seat the rubber face on the mallet head.

FOOTKITS (MIIIFS & MIIIFN)

Both the MIIIFS and MIIIFN tools come supplied with an additional Flooring Foot that can be fitted to offer extra

stability when the tool is in use.

Fitting Instructions:

1. Remove the flat head cap screws (Fig. 9a) and plastic spacer (Fig. 9b) located on the underside of the tool.

Note (MIIIFN Only): also remove the 2 front pads (Fig. 9c).

2. Install the pre-finished flooring foot and the proper number of shims (Fig. 10A) as follows:

NOTE: FLOORING PRODUCTS WILL VARY AND THE USER MUST INSURE THE THE TOOL IS SHIMMED PROPERLY

ACCORDING TO THE FLOORING PRODUCT BEING INSTALLED. ONCE PROPERLY SHIMMED, ONLY THE FOOT

WILL CONTACT THE FLOORING.

3. Re-install the flat head screws.

4. Roller adjustment (Fig 11): the tool is shipped with rollers set-up for 5/8”- 3/4” (Fig. 11a) range flooring. For

1/2”- 9/16” range flooring remove o-rings, shafts, rollers and re-install rollers in upper holes (Fig. 11b).

Note: If desired or if proper range of adjustment cannot be achieved, foot may be used without rollers.

FLOORING FOOT INSTRUCTIONS

1. Be sure the foot is flush to the flooring (Fig. 12a). Use the window to verify this (Fig. 12b).

Important: DO NOT STRIKE PRE-FINISHED FLOORING (Fig. 12c)

2. Strike both sides of the foot to set the flooring (Fig. 13a).

3. Actuate the tool after flooring is set (Fig. 13b) and then roll the tool to the next fastener position

CORRECT FASTENER PLACEMENT

When the tool is properly shimmed and with the correct air pressure, the fasteners should be set into the flooring

tongue. (Figs. 14A,B,C). However, some adjustment may be required to ensure the correct drive depth as follows:

Important: Always test on a scrap piece of flooring first.

Shims Recommended:

Flooring Thickness

1/2” (12.7mm)* 3/4” (19mm)

MIIIFN 21

MIIIFS 10

* 1/2” Flooring: remove the bumper spacer (p/n

118076). This is item 22 on your tool parts

illustration.

Fig. 14a

• Air pressure too low.

• Fastener above tongue.

• Increase air pressure.

Fig. 14b

• Air pressure too high.

• Fastener buried.

• Lower air pressure.

Fig. 14c

• Correct air pressure.

• Fastener just below surface.

FT71556-b-0210_Flooring_Tools_Manual:FT71556 15/4/11 09:42 Page 7

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this

document do not constitute CE compliance for the products.

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées

de ce document ne signifient en rien que les produits soient conformes aux normes CE.

D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte

Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.

NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige

kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.

DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument

udgør ikke CE overholdelse for produkterne.

SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt

kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.

G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη

εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

τα προϊόντα.

I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo

documento non garantiscono la conformità CE per i relativi prodotti.

N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette

dokumentet oppfyller ikke kravene for CE-merking for produktet.

P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas

deste documento não estão em conformidade com a CE para os produtos.

documento no suponen la conformidad con las normas CE de los productos.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

dokumentu nie sú v súlade s CE pre dané výrobky.

sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch MIIIFN in the language / languages: All languages as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bostitch MIIIFN Manual

Product: