721914
6
Zoom out
Zoom in
Previous page
1/68
Next page
Note (MFN201): Because it is a manual tool, sufficient force is required when using the MFN201 to completely
drive flush a single fastener with one strike of the hammer. Do not use the hammer twice on the same fastener,
unless the ratcheting mode is engaged.
Note (MFN201, MIIIFS, MIIIFN): Never hit the plunger with the metal face of the hammer.
CAUTION (MIIIFS & MIIIFN): Installing Pre-finished Flooring
These tools were designed for use in installing unfinished hardwood flooring. They can be used to install pre-
finished flooring, however caution must be used to ensure that the finish is not damaged by the tool. It is
recommended that the tools be tested on a sample section to be certain that the tool and technique of use do
not leave marks on the finish. This procedure should be followed before each job due to variations in flooring
and tool condition.
LOADING THE TOOL
MFN201 (Fig. 4)
1. Release the pusher spring clip and remove pusher blade. (fig 4a)
2. Load fasteners into guide channel.
3. Insert rounded end of pusher blade into channel to retain fasteners.
4. Latch pusher spring clip to notched end of pusher blade. Ensure sufficient engagement ofpusher blade for
smooth fastener feeding. (fig 4b)
MIIIFS (Fig. 5)
1. Pull cover open and insert stick of staples.
2. Push cover forward until the pin snaps into place, locking the cover.
MIIIFN (Fig. 6)
1. Insert nails.
2. Pull pusher assembly back (fig 6a) to engage pusher to strip of nails.
Note: Use only fasteners recommended by Bostitch for use in Bostitch tools or fasteners that meet Bostitch
specifications.
TOOL MAINTENANCE
CAUTION: Pusher spring (constant force spring). Caution must be used when working with the
spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its
length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your
hand. Also, the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent
kinks are put in the spring as this will reduce the spring’s force.
MALLET MAINTENANCE
Over time the rubber face on the mallet may became worn, cracked, or chipped. These are signs that a new
rubber face will need to be installed.
To remove old rubber face:
1. Secure the rubber face in a bench vise. (Fig 7)
2. Pull upward on the handle till the rubber face is released from the steel stud.
To install a new rubber face on the mallet, we recommend doing it in the shop with the use of an arbor press. If
you must do it manually follow these instructions.
1. Secure the mallet head in a bench vise. (Fig 8)
FT71556-b-0210_Flooring_Tools_Manual:FT71556 15/4/11 09:42 Page 6
GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
DK ©Stanley Bostitch. ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
udgør ikke CE overholdelse for produkterne.
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
τα προϊόντα.
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
documento non garantiscono la conformità CE per i relativi prodotti.
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
dokumentet oppfyller ikke kravene for CE-merking for produktet.
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
deste documento não estão em conformidade com a CE para os produtos.
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
dokumentu nie v súlade s CE pre dané výrobky.
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bostitch MFN201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch MFN201 in the language / languages: All languages as an attachment in your email.

The manual is 2,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info