721897

Bostitch FN1664-E Manual

9
Zoom out
Zoom in
Previous page
1/58
Next page
GB
3. Open the jam clearing nose door by pulling down and
then up on the latch (FN1664-E / FN1664SP-E only - Fig
10).
4. Remove the jammed fastener. In certain circumstances,
pliers may be required to remove the fastener.
5. Close the jam clearing nose door latch (FN1664-E /
FN1664SP-E only - Fig 11).
6. Pull pusher back behind fasteners (FN1664-E /
FN1664SP-E) or close the magazine (BT1855-E,
BT1855SP-E, FN1650, FN1650SP-M, SX1838-E, SL540-M).
“DIAL-A-DEPTH™” FASTENER CONTROL
ADJUSTMENT (FIG 12A / 12B)
The DIAL-A-DEPTH™ Fastener Control adjustment
feature provides close control of the fastener drive depth;
from flush with the work surface to shallow or deep
countersink. First, set the air pressure for consistent
drive in the specific work, then use the DIAL-A-DEPTH™
Fastener Control adjustment to give the desired depth of
drive.
TRIGGER LOCKOUT CONTROL - BT1855-E, SX1838-E,
FN1664-E, FN1650 ONLY (FIG 13)
The trigger lockout control feature on BOSTITCH
pneumatic tools provides a trigger lock feature for added
safety control. Push the Lockout control button in or out
to activate or lock the tool trigger.
ACTUATION MODE
m
Warning! Always disconnect air supply before making
adjustments as accidental actuation may occur, possibly
causing injury.
SAFETY YOKE TYPE - BT1855SP-E, FN1650SP-M,
FN1664SP-E ONLY
These models operate dierently from all other
BOSTITCH tools. To provide maximum visibility for
accurate fastener placement, the safety yoke of this tool
is normally in the “depressed” or “up” position. On all
other BOSTITCH tools and most other tools, the safety
yoke is normally in the “extended” or “down” position.
This tool has a selectable actuation mode which
determines if the tool drives fasteners in sequential or
contact actuation mode. In sequential mode, when the
tip of the nose is placed on the work surface and the
trigger is pulled, the safety yoke moves out from the tool
to detect the work surface. The tool nose tip must be in
contact with the work surface to actuate. If the safety
yoke does not detect the work surface close enough to
the nose of the tool, the tool will not actuate.
In contact actuation mode, when the trigger is depressed
and held, the safety yoke will move out from the tool.
Contacting the work surface with the tool nose, will
actuate the safety yoke driving a fastener each time the
work surface is contacted.
SELECTABLE ACTUATION SYSTEM - ALL MODELS
These models feature a selectable actuation system that
allows the user to choose between the following modes
of operation.
m WARNING!
Tools marked with this symbol
have either contact actuation, continuous
contact actuation or selectable actuation
with contact actuation selected.
WHEN IN CONTACT ACTUATION MODE:
These tools are designed for use in production
applications such as pallets, furniture,
manufactured housing or upholstery.
DO NOT use for applications such as closing boxes
or crates and fitting transportation safety systems
on trailers and lorries. This tool shall only be used in
safe working places. Care must be taken to prevent
accidental actuation when changing from one
working position to another.
SEQUENTIAL ACTUATION
The sequential actuation requires the operator to hold
the tool against the work with the safety yoke depressed
before pulling the trigger. In order to drive additional
fasteners, the trigger must be released and the tool
lifted away from the work, before repeating the above
mentioned steps.
This makes accurate fastener placement easier, for
instance on framing, toe nailing and crating applications.
The sequential actuation allows exact fastener location
without the possibility of driving a second fastener on
recoil, as described under Contact Trip (below). The
sequential actuation tool has a positive safety advantage
because it will not accidentally drive a fastener if the tool
is contacted against the work - or anything else - while
the operator is holding the trigger pulled.
CONTACT ACTUATION
The common operating procedure on “Contact
actuation” tools is for the operator to actuate the
safety trip while keeping the trigger pulled, thus driving
a fastener each time the work is contacted. This will
allow rapid fastener placement on many jobs, such as
sheathing, decking and pallet assembly. All pneumatic
tools are subject to recoil when driving fasteners.
The tool may bounce, releasing the safety yoke and
if unintentionally allowed to re-contact the work
surface with the trigger still actuated (finger still
holding the trigger pulled) an unwanted second
fastener will be driven.
9
© BOSTITCH 2019
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bostitch FN1664-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch FN1664-E in the language / languages: All languages as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info