497406

Bose FreeSpace 4400 Manual

41
Zoom out
Zoom in
Previous page
1/70
Next page
38 of 66
6.0 FreeSpace
®
4400 System Setup
Input gain setup sequence
1. Set Opti-source
®
Control to Off. This allows you make the
initial gain setting.
2. Select the source Type and determine if Mic Power +12V is
needed. Set Mic Power to On if required. Leave it in the Off
setting if you are using line inputs.
3. Start your input source and monitor its signal on the gain
signal level meter. If the level is green, go to step 4. If the
level is yellow, increase the input gain until the level is green.
Likewise, if the level is red, reduce the input gain until the
level is green.
Programmer’s Note: You may have to repeat step 3 a
few times if the input source is a CD player. The output
level of a CD player varies based on the program material.
4. Set Opti-source to On. If you are using a source that
produces a varying output level due to program material,
such as a CD player, Opti-source leveling will compensate
for these variances. If your system will be switching among
multiple sources, Opti-source leveling will compensate for
variances among the different sources.
5. Repeat steps 1 to 4 for the remaining system inputs.
When you turn Opti-source on, you should only hear a small
change in volume. If you hear a large increase, raise the input
gain. Likewise, if you hear a large decrease, lower the input gain.
Input gain controls
Type – This setting determines the initial gain and amount of gain
available for the input signal. The following table lists the choices
for each input line.
Mic power +12V – This setting enables/disables +12V phantom
power only for inputs 3 and 4, which are capable of accepting
microphone signals. This power source is used for condenser
type microphones.
Gain slider
– Click and drag the gain slider up/down to set the
input gain. Changes in the slider's position are continuously sent
to the FreeSpace 4400 system so you will hear the change in gain
as it is applied and see the change in the signal level on the meter.
The gain range is dependent on the
Type
setting: 80 dB for Mic; 70
dB for Line.
Programmer’s Note: When setting up the system,
adjust the input gain slider until the meter is green.
Occasional flashes of red are acceptable.
Input gain meter – The input gain meter indicates the average
input signal level of the hardware. The meter is divided into three
color segments:
Amber = Low signal level
Green = Good signal level
Red = High signal level
Signal present indicator – The signal present indicator tells you
if a signal is being received by the hardware:
Inactive = No signal
Green = Good signal
Red = Signal clipping
Opti-source
®
– This is the on/off control for this function. When
on, Opti-source leveling automatically manages the input gain
level so that the full output of the amplifier can be achieved. It
does this by adjusting the input signal level to obtain the desired
amplifier input signal level (+11 dBV). When setting the initial
input gain level, check to make sure that Opti-source control is
Off. If you do not see this setting in the control pane, click on
More to display the Opti-source On/Off boxes.
Programmer’s Note: The Opti-source
®
control state
cannot be changed when the Opti-voice
®
paging system
is on.
The following chart shows how Opti-source
®
system leveling
operates. For sources whose average input signal level is less
than –20 dBV, Opti-source leveling will add 20 dB of gain. For
sources whose average signal level is between –20 and 0 dBV,
Opti-source leveling will add the necessary gain so that the aver
-
age output of the Opti-source function is +11 dBV. Sources
whose average level is greater than 0 dBV will have gain reduc
-
tion applied so that they maintain an average of +11 dBV at the
Opti-source leveling output.
Input signals from –20 to 0 dBV fall within the ideal operating
range for the Opti-source leveling function. This is reflected in the
color scale used for the input gain signal level meter. If your input
signal level is within the green area of –20 to 0 dBV, Opti-source
leveling will effectively manage the input source level.
Input Line Input Type(s) Selection Initial Gain
LINE 1 Line 0
LINE 2 Line 0
AUX MIC/
LINE 3
Line (default)
Mic
0
40
PAGE/MIC/
LINE 4
Line
Mic
Line Page
Mic Page (default)
0
40
0
40
-30-25-20-18-15-13-10 -8 -5 -3 0 3 5 8 10 13 15 18
-15
-7
-1
9
17
25
Gain (dB)
Compression (dB)
Input Signal Level (dBV)
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bose FreeSpace 4400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bose FreeSpace 4400 in the language / languages: English as an attachment in your email.

The manual is 6,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info