818578

Bose Aviation Headset Series II Manual

20
Zoom out
Zoom in
Previous page
1/28
Next page
20
Communication but no
active noise reduction in
both ears.
Problem What to do
In Case of Difficulty
• Make sure that your headset is powered, and that the power switch is “ON.”
• If using DC power from the aircraft, check the aircraft fuse or breaker.
• If using the NICAD battery pack, verify that it is charged.
• If using the alkaline battery pack, verify that:
– batteries are installed with the correct polarity. The negative terminal of
each battery attaches to the springs in the battery holder (refer to step 4
on page 13).
– batteries are fully seated and in contact with the top and bottom contacts
of the battery holder. If necessary, spin the installed batteries once with
your thumbs to fully seat them (refer to step 5 on page 13).
– batteries are fresh.
– the headset plug is fully seated in battery pack (refer to step 11 on page 14).
Check to see if the volume controls are turned too low (rotate up to increase
the volume).
Check the holes at the bottom of each earcup to make sure they are not blocked.
If dust or dirt has built up here, carefully use a small wire or the end of a bent
paper clip to unclog the hole. You may need to remove the microphone to clean
the holes.
• Adjust the earcup fit to create a better seal to your head. Be sure that a hat
or eyeglasses do not interfere with the seal.
• Inspect the seal between the cushion and the earcup. The cushion should
sit on the earcup evenly, without gaps.
• Check the holes at the bottom of each earcup to make sure they are not
blocked. If dust or dirt has built up here, carefully use a small wire or the end
of a paper clip to unclog the hole.
You may need to remove the microphone
to clean the holes.
• Adjust the earcup fit to eliminate the sound.
• Inspect the seal between the cushion and the earcup. The cushion should
sit on the earcup evenly, without gaps.
Check to see if the ear cavity foam liner is missing or severely damaged. If so,
refer to “Care and Maintenance” (page 18).
Active noise reduction
but no (or very low
volume) communication
in both ears.
Reduced active noise
reduction, intermittent
clicking sounds, or
communication distortion
in a loud environment.
Popping sound audible
with headset turned on
in a loud environment.
Low rumbling sound with
the headset turned on in
a quiet environment.
Squealing, whistling, or
chirping sound when the
system is turned on.
Do not attempt to disassemble or service the inside of the earcups or other parts
of the headset. Only the microphone boom assembly, Clear Comfort
TM
cushions,
trim rings, foam liners, headband cover, and foam pad are designed for replace-
ment by the user. For instructions on how to care for your headset and how to
replace the cushions, refer to “Care and Maintenance” (page 18). If problems
persist, contact the Bose
®
Aviation Headset Service Department (page 23).
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bose Aviation Headset Series II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bose Aviation Headset Series II in the language / languages: English as an attachment in your email.

The manual is 8.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info