418941
10
Zoom out
Zoom in
Previous page
1/34
Next page
10
Vorbereitung
Deutsch
Jedes Lautsprechergehäuse erstreckt sich
hinter der Wand bzw. Decke
wie in dem grauen
Bereich „SÄGEN SIE NICHT UM DIE GRAUE ZONE“ auf der Schablone dargestellt
(Abbildung 7) und unterhalb des Gitters. Das Lautsprechergehäuse kann entweder nach
oben oder nach unten weisend eingesetzt werden.
Hinweis:
Vermeiden Sie das Einsetzen des Lautsprechers mit dem Gehäuse nach oben,
wenn niedrige Außentemperaturen auftreten können und wenn ein Luftbefeuchter verwendet
wird. Hierdurch umgehen Sie Probleme durch Kondenswasser.
Wenn Sie die Lage der Probebohrung festlegen, sehen Sie sicherheitshalber auch oberhalb
der Bohrung genügend Platz vor, für den Fall, dass es sich ergibt, dass der Platz unterhalb
nicht ausreicht.
Abbildung 7
Schablone für rechteckige
(links) oder runde
Lautsprecherfront (rechts)
ACHTUNG:
Nach der Installation ist das Lautsprechergehäuse hinter der Wand verborgen.
Führen Sie in diesem Bereich der Wand keinesfalls Schnitte oder Bohrungen aus, und
schlagen Sie keine Nägel ein. Wenn das Lautsprechergehäuse mit Werkzeugen beschädigt
wird, kann der Lautsprecher dadurch zerstört werden.
Elektrische Leitungen, Lüftungskanäle und Rohrleitungen in den Hohlwänden dürfen nicht
beschädigt werden (Abbildung 8). Wenden Sie sich an eine Fachkraft, wenn Sie Hilfe beim
Auffinden derartiger Installationen benötigen.
Abbildung 8
Vorsichtsmaßnahmen bei
verdeckten
Elektroinstallationen (a) und
Rohrleitungen (b) hinter der
Wandoberfläche
•Mit einem Balkenfinder können Sie sicherstellen, dass die Lautsprecheröffnung mindestens
12 cm von einem Balken oder Träger entfernt ausgesägt wird.
Der gewählte Installationsort sollte auf der für beide Lautsprecher geeigneten Höhe liegen.
Gleichzeitig muss der Mindestabstand von 1,5 m zwischen den Lautsprechern
gewährleistet sein.
Beachten Sie die Reihenfolge der Schritte:
1. Wählen Sie zunächst den Installationsort des ersten Lautsprechers.
2. Wählen Sie dann den Installationsort des zweiten Lautsprechers.
3. Verwenden Sie die mitgelieferte Schablone für die Probebohrung und für die Umrisse der
Lautsprecherfront.
5
1
/
2
" (14 cm)
DO NOT
CUT AROUND
GRAY AREA
8
1
/
16
" (20.5 cm)
14
1
/
2
" (36.9 cm)
TAP E
HERE
TAP E
HERE
TAP E
HERE
WHITE CUT OUT AREA
WHITE CUT OUT AREA
Pilot Hole
WARNING: Make sure the spot chosen is safe for cutting. Do not cut through
surfaces that have hazards, such as electrical wiring, conduits or plumbing,
concealed behind them. If you are not sure, consult a professional installer
before you proceed.
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
English &
English &
T
T
ranslations
ranslations
WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.
WARNING: Make sure the spot chosen is safe for
drilling. Do not cut through surfaces that have hazards
concealed behind them, such as electrical wiring,
conduits or plumbing. If you are not sure, consult a
professional installer before you proceed.
WARNING: Make sure the spot chosen is safe for
drilling. Do not cut through surfaces that have hazards
concealed behind them, such as electrical wiring,
conduits or plumbing. If you are not sure, consult a
professional installer before you proceed.
WARNING: Make sure the
spot chosen is safe for
drilling. Do not cut through
surfaces that have hazards
concealed behind them,
such as electrical wiring,
conduits or plumbing. If you
are not sure, consult a
professional installer before
you proceed.
WARNING: Make
sure the spot chosen
is safe for drilling. Do
not cut through
surfaces that have
hazards concealed
behind them, such
as electrical wiring,
conduits or
plumbing. If you are
not sure, consult a
professional installer
before you proceed.
WARNING: Make sure the spot chosen is safe
for drilling. Do not cut through surfaces that have
hazards concealed behind them, such as
electrical wiring, conduits or plumbing. If you
are not sure, consult a professional installer
before you proceed.
WARNING: Make sure the spot
chosen is safe for drilling. Do not cut
through surfaces that have hazards
concealed behind them, such as
electrical wiring, conduits or plumbing.
If you are not sure, consult a
professional installer before you
proceed.
9" (22.9 cm)
TAPE
HERE
Translations below
TAP E
HERE
TAPE
HERE
TAPE
HERE
WHITE CUT OUT AREA
WHITE CUT OUT AREA
Pilot Hole
WARNING: Make sure the spot chosen is safe for cutting.
Do not cut through surfaces that have hazards, such as
electrical wiring, conduits or plumbing, concealed behind
them. If you are not sure, consult a professional installer
before you proceed.
DO NOT
CUT AROUND
GRAY AREA
WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.
WARNING: Make sure the spot chosen is safe for
drilling. Do not cut through surfaces that have hazards
concealed behind them, such as electrical wiring,
conduits or plumbing. If you are not sure, consult a
professional installer before you proceed.
WARNING: Make sure the spot chosen is safe for
drilling. Do not cut through surfaces that have hazards
concealed behind them, such as electrical wiring,
conduits or plumbing. If you are not sure, consult a
professional installer before you proceed.
WARNING: Make sure the spot
chosen is safe for drilling. Do not cut
through surfaces that have hazards
concealed behind them, such as
electrical wiring, conduits or plumbing.
If you are not sure, consult a
professional installer before you
proceed.
TAPE
HERE
Translations below
TAPE
HERE
English &
English &
T
T
ranslations
ranslations
TAPE
HERE
WARNING: Make
sure the spot chosen
is safe for drilling. Do
not cut through
surfaces that have
hazards concealed
behind them, such
as electrical wiring,
conduits or
plumbing. If you are
not sure, consult a
professional installer
before you proceed.
WARNING: Make
sure the spot chosen
is safe for drilling. Do
not cut through
surfaces that have
hazards concealed
behind them, such
as electrical wiring,
conduits or
plumbing. If you are
not sure, consult a
professional installer
before you proceed.
WARNING: Make sure the spot
chosen is safe for drilling. Do not cut
through surfaces that have hazards
concealed behind them, such as
electrical wiring, conduits or plumbing.
If you are not sure, consult a
professional installer before you
proceed.
TAPE
HERE
TAPE
HERE
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
DO NOT
CUT AROUND
GRAY AREA
NICHT AUSSÄGEN
Die große graue Zone zeigt
den für das
Lautsprechergehäuse
erforderlichen Raum hinter
der Wandoberfläche an.
Bei der Schablone gibt es
zusätzlich kleinere graue
Bereiche, die ebenfalls nicht
auszusägen sind.
HIER AUSSÄGEN
Die große weiße Zone zeigt
den auszusägenden Bereich
für die Lautsprecherfront an.
Auf der rechten Schablone
befinden sich kleine Kreise
außerhalb der weißen Zone,
welche die Lage der
Bohrungen angeben, die nur
für die runde
Lautsprecherfront
erforderlich sind.
(a)
(b)
HD OG GER.book Page 10 Tuesday, July 8, 2003 4:40 PM
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bose 191 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bose 191 in the language / languages: German as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bose 191

Bose 191 User Manual - English - 34 pages

Bose 191 User Manual - Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info