601016
24
Zoom out
Zoom in
Previous page
1/32
Next page
en Faults and what to do about them
24
3 Faults and what to do about them
Faults and what to do about them
Faults Cause/remedy
ð on the display panel
and drying has been
interrupted.
Empty the condensate container and press the Start button ~ Page 19.
If the optional condensation drain* is installed, the drain hose may be
blocked or kinked. Check the hose for deposits and flush the hose out. Lay
the hose without any kinks.
é on the display panel. Clean the fluff filter and press the Start button ~ Page 18.
SelfCleaning on the ó
display panel.
Not a fault. The heat exchanger is cleaned automatically. Do not pull out
the condensate container while this is displayed.
Dryer does not start. Mains plug plugged in or fuse checked?
Programme selected? Select a programme.
Dryer door open? Close the door.
Childproof lock activated? Deactivate the childproof lock.
"Ready in" time selected? Programme starts after a delay ~ Page 15.
Creasing. Creasing occurs when you have exceeded the maximum load or selected
the wrong programme for the type of fabric. All the required information
can be found in the programme table ~ Page 13.
Remove clothes immediately after drying; creasing may occur if they are
left in the drum.
Water is leaking out. Not a fault; the dryer may be positioned on an incline. Level the dryer.
Laundry is not dried cor-
rectly or is still too damp.
After the end of the programme, warm laundry feels damper than it actually
is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does not
increase the temperature. Your laundry will become drier ~ Page 15.
Select a programme with a longer drying time or increase the drying level.
This does not increase the temperature.
Select a timed programme for subsequent drying of laundry that is still
damp ~ Page 13.
If you have exceeded the maximum load for the programme, the laundry
may not be dried properly.
Clean the moisture sensor in the drum. A fine layer of limescale may
adversely affect the performance of the sensors and your washing will not
dry properly ~ Page 22.
Drying has been interrupted as a result of a power cut, because
the condensate container is full or because the maximum drying time has
been exceeded.
Note: See also the laundry tips ~ Page 12.
* depending on the model
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch WTW83460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch WTW83460 in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch WTW83460

Bosch WTW83460 User Manual - German - 32 pages

Bosch WTW83460 User Manual - Dutch - 32 pages

Bosch WTW83460 User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info