746793
41
Zoom out
Zoom in
Previous page
1/48
Next page
Help with the appliance en
41
3 Help with the appliance
Help with the appliance
Faults Cause/Remedy
Appliance does not start. Check the mains plug and the fuses.
Creasing. Load exceeded or incorrect programme selected for a type of fabric.
All the required information can be found in the programme
table.~ Page 22
Remove laundry from the drum as soon as the drying programme
has finished. Creasing occurs when clothing is left in the drum.
Water is leaking out. The appliance may be positioned at an angle. Level the appliance.
In the base unit, make sure that:
The heat exchanger cover is properly locked.
There is no dirt or debris on the heat exchanger cover's seal.
~ Page 38
If the optional drain hose* is installed, make sure that the drain hose
is correctly connected. ~ Page 34
The appliance is paused but the
drum is turning.
The appliance has detected a high temperature and has started the
CoolDown process. Temperature regulation can take up to 10 minutes.
You can cancel the CoolDown process at any time by opening the door.
The programme does not start Make sure that:
The door is closed
The E 3 sec. (Child lock) has been deactivated
You have pressed Start/Pause
Note: If the programme has been delayed by setting Finished in, the pro-
gramme starts at a later point.
Programme duration displayed
changes as drying progresses.
Not a fault. The moisture sensor measures the residual moisture in the
laundry and adjusts the programme duration (with the exception of timed
programmes).
Laundry is not dried properly or
is still too damp.
After the programme has ended, warm laundry feels damper than it
actually is. Spread out the laundry and let it cool down.
Adjust the drying time or increase the degree of dryness. This will
extend the drying time but the temperature will remain the same.
Select a timed programme to add extra drying time for laundry that is
still damp.
Select a timed programme for a small load.
Do not exceed the maximum load for a programme.~ Page 22
Clean the moisture sensor in the drum. The sensor may become cov-
ered in a fine layer of limescale or detergent and care product resi-
due, which then impairs its performance.~ Page 37
Drying has been interrupted as a result of a power cut, because the
condensation container is full or because the maximum drying time
has been exceeded.
Note: See also the laundry tips.~ Page 25
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch WTR85V21GB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch WTR85V21GB in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info