7
Overview a
Programmes ° max.
T
Additional functions; infor
L Cottons ª¥Ê - 90 °C
7 kg/
4 kg*
Hard-wearing fabrics, heat-resistant fabrics made of
cotton or linen
2(Rinse plus)
ĈSpeedPerfect * ª¥Ê - 90 °C 2(Rinse plus); shorter programme
ćEcoPerfect ª¥Ê - 90 °C 2(Rinse plus); energy-saving programme
7Prewash ª¥Ê - 90 °C 2(Rinse plus); prewash at 30 °C
SEasy-iron ª¥Ê - 90 °C 2(Rinse plus); special spin sequence with subsequent fluffing.
IEasy-Care ª¥Ê - 60 °C
3 kg
Easy-care fabrics made of cotton, linen, synthetic
fibres or blended fabrics
2(Rinse plus)
ĈSpeedPerfect ª¥Ê - 60 °C 2(Rinse plus); shorter programme
ćEcoPerfect ª¥Ê - 60 °C 2(Rinse plus); energy-saving programme
7Prewash ª¥Ê - 60 °C 2(Rinse plus); prewash at 30 °C
LIFMix ª¥Ê - 40 °C Fabrics made of cotton or easy-care fabrics
2(Rinse plus);
different types of laundry can be washed together
cDelicates / Silk ª¥Ê - 40 °C
2 kg
For
synthetic fibres or blended fabrics (e.g. curtains)
2(Rinse plus);
no spin between rinse cycles
:/ /c Wool ª¥Ê - 40 °C
Handä or machine-washable fabrics made of wool or
containing wool
Particularly gentle wash programme to prevent shrinkage of laun-
dry. Longer programme breaks (fabrics rest in the detergent solu-
tion)
@SuperQuick 15’ ª¥Ê - 40 °C
Easy-care fabrics made of cotton, linen, synthetic
fibres or blended fabrics
Short programme, approx. 15 minutes,
suitable for lightly soiled laundry
Additional programmes c Rinse / Spin, > Drain
* reduced load
As a short programme, LIF Mix 40 °C, with the maximum spin speed is ideal.
Programmes without pre-wash - add detergent to compartment II , programmes with pre-wash - distribute the detergent between compartments I and II .
9401 / 9000964638
*964638*
WAE28267SN ..
Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München / Germany
8
Safety instructions
– Read the ins
machine and act accordingly.
– Retain
Risk of electric shock – Never pull the cable to disconnect the mains plug.
– Never insert/discon
Danger to life For worn-out appliances:
– Discon
– Sever the mains cable and dis
– Destroy the lock on th
locking themselves in and risking their lives.
Danger of suffocation – Keep packaging, film and packaging parts out of the reach of children.
Risk of poisoning – Keep detergents and care products out of the reach of children.
Risk of explosion – Items of laund
remover/cleaning solvent may cause an explosion after being loaded into the
washing machine.
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury – The washi
– Be careful when drai
– Do not cli
– Do not lean
– Do not reach
– Be careful when openin
Consumption values depending on model
Programme Load Electricity** Water**
Programme
duration
**
LCottons 20 °C 7 kg 0,31 kWh 72 l 2 ¾ h
LCottons 40 °C 7 kg 0,85 kWh 72 l 2 ¾ h
LCottons 60 °C 7 kg 1,21 kWh 72 l 2 ¾ h
LCottons 90 °C 7 kg 2,01 kWh 77 l 3
Easy-Care 40 °C 3 kg 0,64 kWh 56 l 1 ¾ h
LIFc Mix 40 °C 3 kg 0,46 kWh 36 l 1 ¼ h
cDelicates/Silk 30 °C 2 kg 0,24 kWh 37 l ¾ h
:ü/ / Wool 30 °C 2 kg 0,22 kWh 47 l ¾ h
Programme Additional function Loa
Annual energy
consumption
Annual water
consumption
LCottons ć EcoPerfect 40/60 °C * 3,5/7 kg 165 kWh 10686 l
* Pro
** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
8
9
Care
Before washing for th
Do not load any laundry into the machine. Turn on the tap.
Add the following to compartment II :
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the
appropriate degree of water hardness)
Set the programme I Easy-Care 60 °C and select $ (Start /Pause). At the
of the programme, turn the programme selector to Off .
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
Cleaning the detergent drawer and housing...
... if it contains detergent or fabric softener residues.
1. Pull the drawer out, press down the insert and fully remove the drawer
from the housing.
2. To remove the insert: press the insert upwards from below with your
finger.
3. Clean
dry it. Also remove any detergent or fabric softener residues in the
housing.
4. Attach the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Leave the detergent drawer open so that any residual water can
evaporate.
W
Wipe
that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel wool.
Descaling Ensure there is no laundry in the machine
Descale
be necessary if the correct dosage of detergent is used.
Information on the display panel depending on model
E3 Cl
E5 O
Clean the filter a page 10 , Water pressure too low.
E6 Da page 10.
Drainage a .
E2 M
– Risk of electric shock.
Disconnect the mains plug.
– Risk of explosion. No solvents.
1
Maintenance
Detergent solution pump
Turn the programme selector to Off and disconnect the mains plug.
1. Open and remove the service flap.
2. For models Remove
retainer and pull it from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
2* For Carefully
until the detergent solution begins to flow out. When the service flap is
half full, close the pump cover and empty the service flap. Repeat the
above steps until all the detergent solution has completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean
the detergent solution pump must rotate).
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during the next wash:
Pour 1 litre of water into compartment II and start the >Drain programme.
Drainage hose at the siphon
Turn the programme selector to Off and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose
(residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose
clamp.
Filter in the water suppl
Risk of electric shock
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except 2 Rinse/c Spin // > Drain).
3. Select $ (Start/Pause). Let the programme run for approximately
40 seconds.
4. Turn the programme selector to Off. Disconnect the mains plug.
Clean the filter:
1. Depending on model:
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and HydroSafe models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
– Risk of scalding.
Allow the detergent solution to cool down.
– Turn off the tap.
1
What to do if ...
ʑ
Water is leaking out. – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not
dispensed.
– $ (Start/Pause) not selected?
– Tap not turned on?
– Filter blocked? Clean the filter a page 10.
– Supply hose kinked or trapped?
ʑ
Washing
cannot be opened.
– Safety function active. Wait approx. 2 minutes.
– - - - - (without final spin) selected? a page 3, 4.
ʑ
Programme does not
start.
– $ (Start/Pause) or (Finished in) selected?
– Washing machine door closed?
– Childproof lock active? Deactivate a page 5 .
ʑ
Detergent solution is
not drained.
– - - - - (without final spin) selected? a page 3, 4.
– Clean the detergent solution pump a page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large
– Programme S Easy-iron selected? a page 7.
– Speed selected too low? a page 5 .
ʑ
The programme
duration changes
during the wash cycle.
– Not a fault – the programme sequence is optimised for the
particular wash process. This may result in changes to the
programme duration in the display field.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary a page 9 .
ʑ
Odour formation in the
washing machine.
– Run programme L Cottons 90 °C without laundry. Use standard
detergent.
ʑ
1(Wash)
flashes. Foam may be
coming out of the
detergent drawer.
– Too
½ litre of water and pour into dispenser II (not for outdoor and
down-filled textiles!).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense
vibrations and
“wandering”
spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet a Installation instructions .
– Transportation safety devices removed?
Remove the transportation safety devices a Installation
instructions.
ʑ
Noises
drain cycles.
– Clean detergent-solution pump a page 10.
ʑ
Display
lamps do not function
during operation.
– Power cut?
– Fuses triggered? Reset/change the fuses.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault -
by repeatedly distributing the laundry.
– Not
cycle.
ʑ
Detergent residues on
the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select 2 Rinse /c Spin or brush the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service a Installation instructions.
en operating instructions
Washing machine
WAE28267SN
