Manual Bosch UniversalVerticut 1100 (page 19 of 303) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

777044

Zoom out

Zoom in

1/303

English | 19

Note: In conditions with excessive tree debris (e.g. leaves,

twigs, etc.), first clear the surface by using the product with

the working height set to 3 or 4.

For best results mow the lawn before reseeding. Promote

the spread of grass into bare and weak areas with good qual-

ity lawn seed after raking/verticutting. Allow fresh grass

seed to root and establish before fertilising, where neces-

sary water to prevent fresh seeds drying out.

Ideal times for raking/verticutting are spring and late au-

tumn.

Lawns can also be maintained by raking/verticutting on a

higher setting after every six cuts.

Troubleshooting

The following chart lists problem symptoms, possible causes and corrective action, if your product does not operate properly.

If these do not identify and correct the problem, contact your service agent.

uWarning: Switch off and remove plug from mains be-

fore investigating fault.

Problem Possible Cause Corrective Measure

Garden tool does not

operate Power turned off Turn power on

Mains socket faulty Use other socket

Extension cable damaged Inspect cable, replace if damaged

Fuse faulty / blown If fuse blows continuously, please check your

electricity supply system or contact Bosch cus-

tomer service agent

Possible clog Check underneath the garden product and clear

out as necessary (always wear protective gloves)

Safety cut out is active (only UniversalVerti-

cut1100) See below A)

Setting for raking/verticutting too low for the con-

ditions Increase working height

Obstructed rotor Clear obstruction (always wear protective gloves)

Blocked side grilles Clear debris from the outside of the side grilles

Grassbox full Empty the grassbox regularly

Garden tool runs inter-

mittently Extension cable damaged Inspect cable, replace if damaged

Internal wiring of garden tool defective Contact Bosch customer service agent

Worn/Missing tines/blades Contact Bosch customer service agent

Conditions too wet Increase working height (see "Tips for Raking/Ver-

ticutting Lawns")

Too much debris on the ground See below A)

Possible clog Check underneath the garden tool and clear out

as necessary (always wear protective gloves)

Setting for raking/verticutting too low for the con-

ditions Increase working height

Grass too long Cut grass

Very uneven surface Increase working height

Grassbox full Empty the grassbox regularly

Garden tool runs stiffly

or belt squeaks Working height too low Increase working height (see "Adjusting the Work-

ing Height")

Cutting tines/blades

not rotating Cutting tines/blades obstructed by grass Clear obstruction (always wear protective gloves)

Belt slipping or damaged Contact Bosch customer service agent

Excessive vibrations/

noise Cutting tines/blades damaged Contact Bosch customer service agent

Poor work perform-

ance Ground too moist for raking/verticutting Increase working height (see "Tips for Raking/Ver-

ticutting Lawns")

Bosch Power Tools F 016 L94 116 | (17.02.2021)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalVerticut 1100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 5.58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch UniversalVerticut 1100 Manual

Product: