Manual Bosch UniversalMulti 12 Multitool (page 20 of 145) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708268

Zoom out

Zoom in

1/145

20 | English

1 609 92A 3AY | (3.3.17) Bosch Power Tools

Note: If the machine should automatically switch off because

of a discharged or overheated battery, make sure to set the

machine’s On/Off switch 2 to off. Charge the battery and

allow it to cool down before restarting the machine. Other-

wise the battery can become damaged.

Removing the battery

To remove the battery 3, press the unlocking buttons 4 and

pull the battery out of the machine to the rear. Do not exert

any force.

Battery Charge-control Indication

When the power tool is switched on, the battery charge-

control indicator 6 signals the still available battery capacity

or an overload.

When the battery charge-control indicator 6 flashes red, the

machine is subject to overload. Please observe the infor-

mation in section “Temperature-dependent Overload Protec-

tion”, page 25.

Changing the Tool

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Wear protective gloves when changing application

tools/accessories. Contact with the application tool/

accessory can lead to injuries.

Please observe the application tools/accessories intended

for your tool.

Selecting the Application Tool/Accessory

The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-

sories program.

Indication Capacity

Continuous lighting, green >70 %

Continuous lighting, yellow 30–70 %

Continuous lighting, red <30 %

Accessory UniversalMulti 12

Accessory Material Application

BIM segment saw

blade

Wooden materials,

Plastic,

Non-ferrous metals

Separating and plunge cuts; also for sawing close to edges,

in corners and hard to reach areas;

example: shortening already installed bottom rails or door

hinges, plunge cuts for adjusting floor panels

Base plate for

sanding, series

Delta 93 mm

Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach

areas;

depending on the sanding sheet for, e.g., sanding wood,

paint, varnish, stone

Fleeces for cleaning and for texturing wood, removing rust

from metal and for keying varnishes, polishing felt for pre-

polishing

Profile sander

Wood,

Pipes/Profile,

Paint,

Varnishes,

Filler,

Metal

Convenient, efficient sanding of profiles up to a diameter of

55 mm;

Red sanding sheets for sanding wood, pipes/profiles, var-

nishes, fillers and metal

BIM plunge cut

saw blade, wood

and metal

Softwood,

Soft plastics,

Plasterboard,

Thin-walled aluminium

and non-ferrous metal

profiles,

Thin sheet metals,

Non-hardened nails and

screws

Smaller separating and plunge cuts;

example: cutting an opening for sockets, flush cutting a

copper pipe, plunge cuts in plasterboard

Filigree adjustment work in wood;

example: sawing openings for locks and fittings

OBJ_BUCH-2957-001.book Page 20 Friday, March 3, 2017 2:20 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalMulti 12 Multitool in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch UniversalMulti 12 Multitool Manual

Product: